EarthQuake MODEL 3365K, R3355H, MODEL 3365PS, 3365PSCE Operation, PRE-START Inspection, Start-Up

Page 10

OPERATor INSTRUCTIONS and parts

Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE

Operation

PRE-START INSPECTION

1.Make sure all safety guards are in place and all nuts and bolts are secure.

2.Check oil level in engine crankcase. See your engine manual for procedure and specifications.

3.Inspect air cleaner for cleanliness. See your engine manual for procedure.

4.Check the fuel supply. Fill the fuel tank no closer than one inch from top of tank to provide space for expansion. See your engine manual for fuel recommendations.

5.Be sure spark plug wire is attached and spark plug is tightened securely.

6.Check position of wheels.

7.Check depth regulator lever position.

8.Examine underneath and around engine for signs of oil or fuel leaks.

9.Inspect fuel hoses for tightness and fuel seepage.

10.Look for signs of engine damage.

11.Remove excessive debris from muffler area and recoil starter.

12.Turn fuel shutoff valve to the ON position if engine is equipped with one. It’s located between tank and carburetor.

START-UP

For models 3365, 3365B, 3365CE, 3365K, 3365KPS, and 3365PS only.

The controls required to start and run the rototiller are located on the engine and are marked Choke and Throttle.

A more detailed description of engine operation and all related precautions and procedures can be found in the engine manufacturer’s manual that accompanies each tiller.

Cold Starts

1.Move choke lever to full choke position.

2.Move throttle lever to start.

3.Pull starting rope out slowly one time and allow to return normally.

4.Pull starting rope out rapidly and allow rope to return normally.

5.When engine starts, gradually move choke lever to no choke position and increase throttle speed.

Restarting A Warm Engine

Restarting an engine that is already warm from previous running does not normally require the use of the choke.

1.Move throttle lever to start position.

2.Pull starting rope out rapidly until engine starts. Allow rope to return normally. Repeat until engine starts.

3.Adjust throttle speed to high for best tiller action.

IMPORTANT

Engine is shipped from factorywithout oil.

YOU MUST ADD ENGINE OIL BEFORE STARTING ENGINE.

Practice operating the controls and tiller with tines out of ground before beginning to till. It is important that you know how to use the tiller properly, keep control at all times, stop the tines and wheels from turning, and stop the engine if necessary. If you do not know how to do these things, read the Controls and Safety sections before proceeding.

!CAUTION

Please do not start your tiller until you have read the Manual that came with your engine and the sections in this manual titled “Controls and Safety.” Once you have read these, follow the appropriate stepsto startyourtiller. Always perform this pre-start checklist before starting the engine.

!WARNING

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is hot or running. Always move outdoors to fill the tank.

Temperature of muffler and nearby areas may exceed 150° F. Avoid these areas.

Do not move choke control to CHOKE to stop engine. Backfire or engine damage may occur.

TO STOP THE ENGINE AT ANY TIME, MOVE THROT- TLE CONTROL TO THE OFF POSITION. To stop tines at any time, release drive safety control lever to the neutral position.

Always release drive safety control lever to the neutral position before adjusting the depth of the regulator lever.

Page 10

800-345-6007

GetEarthquake.com

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operating Instructions Page Contents IntroductionSpecial Messages Important Safety PrecautionsOWNER’S Responsibility PreparationMaintenance and storage OperationHood Warning Safety DecalsTines DANGER/OPERATION LBLCENOISE80Unpacking and Assembly Do not TRY to Lift the Rototiller from the CartonFeatures 3365/3365B/3365Ce/3365K Transport Position Operating PositionEngine should be OFF Before Adjusting ANY Controls Drive Safety Control LeverBelt Tension Adjustment ControlsSTART-UP OperationPRE-START Inspection YOU Must ADD Engine OIL Before Starting EngineShutting Down For models R3365H and 3365PSCE onlyOperating Speed TillingMaintenance Operation Before Hours or Maintenance ScheduleServicing the Rototiller Check Belt Tension Belt replacementChange Forward Belt Check or Fill Engine Crankcase Engine MaintenanceClean tine axle shaft LubricationStorage Prepare for StorageTroubleshooting and Repair Troubleshooting Guide3365/3365B/3365ce/3365K Handlebar parts Description QTY3365PS/3365KPS Handlebar parts R3355H/3365PSCE Handlebar parts 3365KPS Bumper SHIELD, Dirt Model 3365PS/3365PSCE Bumper Guard PartsR3355H motor mount & Hood parts Model R3355H BumperModel R3355H Bumper Guard Parts Tines & transmission Parts NUT, Nyloc 1/4Year Limited Warranty Terms and Conditions Front Tine RototillersOPERATor Instructions and parts OPERATor Instructions and parts Benefit you throughout the year

MODEL 3365CE, 3365, 3365B, 3365PSCE, MODEL 3365KPS specifications

The EarthQuake MODEL 3365KPS, 3365PSCE, 3365, MODEL 3365CE, and MODEL 3365PS represent a line of robust and powerful tools designed to meet various construction and landscaping needs. These models are engineered to provide exceptional performance in the most challenging conditions, making them a favorite among professionals and DIY enthusiasts alike.

A standout feature of these models is their heavy-duty construction. Built with high-quality materials, the EarthQuake 3365 series ensures durability and longevity, capable of withstanding the rigors of daily use. They are particularly known for their efficient combustion engines that deliver robust power while maintaining fuel efficiency, allowing users to operate for extended periods without frequent refueling.

One of the key technologies incorporated into the EarthQuake 3365 models is their precision-engineered vibration reduction system. This innovation minimizes operator fatigue during prolonged use, enhancing comfort and productivity on the job. Additionally, the models are equipped with an easy-start mechanism that simplifies ignition, ensuring a hassle-free start every time.

The EarthQuake 3365 series also features adjustable settings that provide versatility for various applications. Whether for digging, tamping, or breaking concrete, these tools can adapt to specific tasks efficiently. The pneumatic wheels on the models enhance mobility, making it easy to maneuver them across different terrains, including rough and uneven surfaces.

Another characteristic that sets the EarthQuake 3365 line apart is its user-centric design. Each model is equipped with ergonomic handles that promote a comfortable grip, allowing for better control and precision during operation. Safety features, such as automatic shut-off mechanisms and protective guards, are also integrated to ensure that users can operate the tools confidently and with reduced risk of accidents.

In summary, the EarthQuake MODEL 3365KPS, 3365PSCE, 3365, MODEL 3365CE, and MODEL 3365PS represent the pinnacle of engineering in construction tools. With their powerful engines, durable construction, user-friendly features, and advanced technologies, these models are ideal for both commercial and residential applications, offering reliable performance and unmatched efficiency for all your tough jobs.
Top Page Image Contents