King Kutter 999995 manual Attaching to Tractor

Page 17

ATTACHING TO TRACTOR continued....

STEP 4

Pull apart PTO shaft and attach outer section to tractor PTO output shaft. NOTE: Be sure to pull on PTO shaft section to ensure yoke has locked into place.

STEP 5

Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too long. Each section should end approximately 1- inch short of reaching u-joint shield on the opposite section. If the shaft is too long measure 1 inch back from each u-joint shield and mark the other shaft section. (Measure 1 inch from arrow on FIG. C on page 18). Be sure to do this for both PTO shaft halves. NOTE: Do not cut PTO shaft sections at this time.

STEP 6

Raise rotary tiller and remove blocking. Raise and lower rotary tiller in order to locate the longest distance between equipment input shaft and the tractor PTO output shaft. With the rotary tiller in the longest distance position shut down the tractor and SECURELY BLOCK THE ROTARY TILLER IN POSITION.

STEP 7

As in step 5 hold PTO shaft sections together and check for a minimum of 6 inches of overlap. If PTO shaft has been marked for cutting the overlap is the distance measured between the two marks. If the PTO shaft has less than a 6 inch overlap, DO NOT USE. Contact your autho- rized King Kutter Dealer.

NOTE

If the PTO shaft length is too long go to SIZING PTO SHAFT (pg. 18)

STEP 8

Apply any multipurpose grease to the outside of the male (inner) PTO shaft section. Assemble PTO shaft and install on rotary tiller and trac- tor.

STEP 9

Pull on tractor side of PTO shaft yoke to be sure it has locked in place. Make certain PTO shaft shielding is in place and good working condi- tion.

STEP 10

The PTO shaft shield is a non-rotating design and must be secured prior to equipment use. Using the chain on each yoke shield attach to a fixed object on the tractor and equipment ends that will not allow the PTO shaft shield to rotate during operation.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents XB Rotary Tiller Page To the Purchaser Page Contents Safety Equipment Safety Guidelines Before Putting Rotary Tiller Into Service XB-ROTARY Tiller Assembly Instructions StepReplace and tighten the plug. Clean away any excess oil Figure D Safety Training Preparation Starting and Stopping SafetyOperational Safety Operational Safety Transport Safety Sharper than 35 Degrees PTO Must be Stopped Attaching to Tractor StepAttaching to Tractor Sizing PTO Shaft Step Operating Instructions Step Maintenance Safety MaintenanceStorage Safety Top View Safety Sign LocationsPage Page Page Page 22 PTO TC-48-XB-TILLER Exploded View TC-48-XB-TILLER Parts List Page Page TC-48-XB Side Gearbox Parts TC-48-XB Side Gearbox Parts List TC-48-XB Series TOP Gearbox Parts TC-48-XB Series TOP Gearbox Parts List Limited Warranty
Related manuals
Manual 36 pages 15.92 Kb

999995 specifications

The King Kutter 999995 is a robust and reliable rotary cutter designed for both agricultural and commercial applications. Known for its durability and efficiency, it stands out as a preferred choice among landowners, farmers, and landscapers who need a dependable tool for land management and brush clearing.

One of the primary features of the King Kutter 999995 is its heavy-duty construction. Built with a rugged, all-steel frame, this rotary cutter is designed to withstand harsh conditions and perform reliably in challenging environments. The cutter’s thick side skirts and reinforced welds provide added strength and support, ensuring that it can handle tough materials like dense brush and thick grass with ease.

Another notable technology incorporated into the King Kutter 999995 is its high-performance blade system. The cutter is equipped with heavy-duty, heat-treated blades that are designed for longevity and superior cutting capability. These blades can be easily sharpened or replaced when necessary, making maintenance simple and ensuring that the cutter remains efficient over time.

The King Kutter 999995 also features a double-gearbox design, which enhances its cutting performance. This dual gear system allows for increased torque, enabling the cutter to tackle tougher materials without bogging down. The gearbox is designed for high-efficiency operation, which minimizes wear and maximizes the lifespan of the machine.

Another key characteristic of this rotary cutter is its compatibility with a wide range of tractors. The King Kutter 999995 is available in a variety of sizes and can be easily attached to both small and large tractors, making it a versatile tool for users with different equipment options. Its user-friendly design allows for quick setup and operation, making it accessible for users of all skill levels.

Safety is also a primary consideration in the King Kutter 999995 design. The cutter is equipped with safety features to minimize the risk of accidents during operation. These include a standard chain guard system that helps prevent debris from flying into the operator's area while cutting.

In summary, the King Kutter 999995 is a top-of-the-line rotary cutter that combines heavy-duty construction, advanced blade technology, and high compatibility with tractors. Its features make it an excellent choice for anyone seeking a reliable tool for land clearing and maintenance, offering both efficiency and safety for various cutting tasks.
Top Page Image Contents