King Kutter Tiller Depth Adjustment and Operating Instructions
Page 19

OPERATING INSTRUCTIONS

WARNING: IF TILLER IS RAISED UP SO THAT PTO SHAFT IS AT AN ANGLE SHARPER THAN 35 DEGREES PTO MUST BE STOPPED!

STEP 1

Before each use perform the maintenance described in maintenance section (page 20).

STEP 2

Read, understand, and follow the information on safety training, preparation, starting and stopping safety, operational safety, transport safety warning sec- tions of this manual (pages 12 thru 15).

STEP 3

With the rotary tiller positioned on level ground, adjust the tractor lift arms so that when lifted, the rotor bar remains parallel to the ground.

STEP 4

With the rotary tiller attached to the tractor, raise and support the tiller with suitable blocks. Adjust the skids, located on the sides of the tiller. The adjust- ment bolts for both right and left sides should be positioned in the same ad- justment hole. This allows the tiller to till the same depth on each side. Adjust the back plate, with regulating chain, until the desired mulching effect is found.

Note: Never attempt to adjust the rotary tiller while the tractor is running.

STEP 5

Raise the tiller and remove the blocks. Lower the tiller to the ground.

STEP 6

With the tractor at idle RPM and the tiller lifted off of the ground, engage PTO and slowly advance throttle to 540 PTO RPM. NOTE: Rotary tiller is designed to run at 540 PTO RPM only.

STEP 7

Select a low gear for the tractor and begin to move forward. Tractor ground speed is to be controlled by gear selection only and not engine speed. As the tractor moves forward, slowly lower the tiller down. Allow the tiller tines to gradually engage the ground.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents XB Rotary Tiller Page To the Purchaser Page Contents Safety Equipment Safety Guidelines Before Putting Rotary Tiller Into Service XB-ROTARY Tiller Assembly Instructions StepReplace and tighten the plug. Clean away any excess oil Figure D Safety Training Preparation Starting and Stopping SafetyOperational Safety Operational Safety Transport Safety Sharper than 35 Degrees PTO Must be Stopped Attaching to Tractor StepAttaching to Tractor Sizing PTO Shaft Step Operating Instructions Step Maintenance Safety MaintenanceStorage Safety Top View Safety Sign LocationsPage Page Page Page 22 PTO TC-48-XB-TILLER Exploded View TC-48-XB-TILLER Parts List Page Page TC-48-XB Side Gearbox Parts TC-48-XB Side Gearbox Parts List TC-48-XB Series TOP Gearbox Parts TC-48-XB Series TOP Gearbox Parts List Limited Warranty
Related manuals
Manual 36 pages 15.92 Kb

999995 specifications

The King Kutter 999995 is a robust and reliable rotary cutter designed for both agricultural and commercial applications. Known for its durability and efficiency, it stands out as a preferred choice among landowners, farmers, and landscapers who need a dependable tool for land management and brush clearing.

One of the primary features of the King Kutter 999995 is its heavy-duty construction. Built with a rugged, all-steel frame, this rotary cutter is designed to withstand harsh conditions and perform reliably in challenging environments. The cutter’s thick side skirts and reinforced welds provide added strength and support, ensuring that it can handle tough materials like dense brush and thick grass with ease.

Another notable technology incorporated into the King Kutter 999995 is its high-performance blade system. The cutter is equipped with heavy-duty, heat-treated blades that are designed for longevity and superior cutting capability. These blades can be easily sharpened or replaced when necessary, making maintenance simple and ensuring that the cutter remains efficient over time.

The King Kutter 999995 also features a double-gearbox design, which enhances its cutting performance. This dual gear system allows for increased torque, enabling the cutter to tackle tougher materials without bogging down. The gearbox is designed for high-efficiency operation, which minimizes wear and maximizes the lifespan of the machine.

Another key characteristic of this rotary cutter is its compatibility with a wide range of tractors. The King Kutter 999995 is available in a variety of sizes and can be easily attached to both small and large tractors, making it a versatile tool for users with different equipment options. Its user-friendly design allows for quick setup and operation, making it accessible for users of all skill levels.

Safety is also a primary consideration in the King Kutter 999995 design. The cutter is equipped with safety features to minimize the risk of accidents during operation. These include a standard chain guard system that helps prevent debris from flying into the operator's area while cutting.

In summary, the King Kutter 999995 is a top-of-the-line rotary cutter that combines heavy-duty construction, advanced blade technology, and high compatibility with tractors. Its features make it an excellent choice for anyone seeking a reliable tool for land clearing and maintenance, offering both efficiency and safety for various cutting tasks.
Top Page Image Contents