King Kutter Official Tiller Manual: XB-Rotary Tiller Assembly and Service Guide
Page 8

XB-ROTARY TILLER ASSEMBLY INSTRUCTIONS

STEP 1

With rotary tiller still in crate, lay flat on a level surface. Cut banding straps on the two (2) upright crate posts.

STEP 2

Remove the top & upper side sections of the crate, leaving the rotary tiller resting on the bottom sec- tion.

STEP 3

Remove tie wire holding the PTO shaft and set aside PTO.

STEP 4

Attach tiller according to your tractors manual and using the instructions on pages 16 and 17.

STEP 5

Install tail back plate chain.

STEP 6

Install PTO shaft as outlined in the Attaching to Tractor Section, pg 16-19.

Note: The safety chains on the PTO shaft should be attached to the tractor and tiller to prevent the plastic safety shield from rotating.

BEFORE PUTTING ROTARY TILLER INTO SERVICE

(IMPORTANT-INSTRUCTIONS PRIOR TO START UP) SHIPPED WITHOUT OIL IN GEAR BOXES AND WITHOUT GREASE IN GREASE FITTINGS. UNIT MUST BE SERVICED BEFORE USING.

•Fill Gearbox using gear oil (type SAE-EP-80W 90.)

•For all Grease Fittings use TYPE/grade II tube grease.

STEP 1 Place rotary tiller so that the deck is secure and level.

STEP 2 Remove Oil Plug (Located at top of transmission gearbox). See Figure A & B.

STEP 3 Fill gearbox using gear oil until gearbox is approximately 1/2 full (16 oz). The plug has marks on it. (See FIgure C) Make sure oil level is close to top line, but not over it. DO NOT OVERFILL!

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents XB Rotary Tiller Page To the Purchaser Page Contents Safety Equipment Safety Guidelines XB-ROTARY Tiller Assembly Instructions Step Before Putting Rotary Tiller Into ServiceReplace and tighten the plug. Clean away any excess oil Figure D Safety Training Starting and Stopping Safety PreparationOperational Safety Operational Safety Transport Safety Attaching to Tractor Step Sharper than 35 Degrees PTO Must be StoppedAttaching to Tractor Sizing PTO Shaft Step Operating Instructions Step Maintenance Maintenance SafetyStorage Safety Safety Sign Locations Top ViewPage Page Page Page 22 PTO TC-48-XB-TILLER Exploded View TC-48-XB-TILLER Parts List Page Page TC-48-XB Side Gearbox Parts TC-48-XB Side Gearbox Parts List TC-48-XB Series TOP Gearbox Parts TC-48-XB Series TOP Gearbox Parts List Limited Warranty
Related manuals
Manual 36 pages 15.92 Kb

999995 specifications

The King Kutter 999995 is a robust and reliable rotary cutter designed for both agricultural and commercial applications. Known for its durability and efficiency, it stands out as a preferred choice among landowners, farmers, and landscapers who need a dependable tool for land management and brush clearing.

One of the primary features of the King Kutter 999995 is its heavy-duty construction. Built with a rugged, all-steel frame, this rotary cutter is designed to withstand harsh conditions and perform reliably in challenging environments. The cutter’s thick side skirts and reinforced welds provide added strength and support, ensuring that it can handle tough materials like dense brush and thick grass with ease.

Another notable technology incorporated into the King Kutter 999995 is its high-performance blade system. The cutter is equipped with heavy-duty, heat-treated blades that are designed for longevity and superior cutting capability. These blades can be easily sharpened or replaced when necessary, making maintenance simple and ensuring that the cutter remains efficient over time.

The King Kutter 999995 also features a double-gearbox design, which enhances its cutting performance. This dual gear system allows for increased torque, enabling the cutter to tackle tougher materials without bogging down. The gearbox is designed for high-efficiency operation, which minimizes wear and maximizes the lifespan of the machine.

Another key characteristic of this rotary cutter is its compatibility with a wide range of tractors. The King Kutter 999995 is available in a variety of sizes and can be easily attached to both small and large tractors, making it a versatile tool for users with different equipment options. Its user-friendly design allows for quick setup and operation, making it accessible for users of all skill levels.

Safety is also a primary consideration in the King Kutter 999995 design. The cutter is equipped with safety features to minimize the risk of accidents during operation. These include a standard chain guard system that helps prevent debris from flying into the operator's area while cutting.

In summary, the King Kutter 999995 is a top-of-the-line rotary cutter that combines heavy-duty construction, advanced blade technology, and high compatibility with tractors. Its features make it an excellent choice for anyone seeking a reliable tool for land clearing and maintenance, offering both efficiency and safety for various cutting tasks.
Top Page Image Contents