Pentair Hydropump warranty Pump will, Not Prime, LOW Flow, Motor, Runs HOT, Not Turn

Page 1

TROUBLE GUIDE

THE FOLLOWING ARE SOME COMMON CAUSES OF PROBLEMS THAT MAY ARISE:

 

PROBLEMS

 

 

 

POSSIBLE CAUSES & SOLUTIONS

A.

PUMP WILL

1.

Make sure pool water is midway of skimmer opening.

 

NOT PRIME:

2.

Make sure strainer basket is not clogged.

 

 

 

3.

Make sure strainer basket is positioned properly!

 

 

 

4.

Tighten lid down snugly.

 

 

 

 

 

5.

Make sure strainer pot is full of water.

 

 

 

6.

TIghten all fittings and seal all joints on suction side.

 

 

 

7.

Clean skimmer and pump strainer baskets.

 

 

 

8.

Remove pump lid and check for clogging.

 

 

 

9.

Open all valves in return and suction lines.

 

 

 

10.

Remove and replace pump seal if needed.

 

 

 

11.

Check voltage at pump to be sure it is same as motor specs.

B.

LOW FLOW

1.

If filter gauge reads high.

 

 

 

 

 

 

a.

Filter is dirty.

 

 

 

 

 

 

 

b.

Clogged return lines.

 

 

 

 

 

2.

If filter pressure gauge reads low.

 

 

 

 

a. Pump or skimmer strainer basket is clogged.

 

 

 

 

b. Skimmer or main drain valve is closed.

 

 

 

 

c. Air leak in suction line.

 

 

 

 

d. Impeller setting is incorrect.

 

 

 

 

e. Debris on impeller vanes.

C.

MOTOR

1.

Motors will run hot to the touch, however, they are designed this way. Thermal

 

RUNS HOT

 

overload protector will function to turn the motor off if there is an overload problem.

 

 

 

2.

Factors which will increase operating temperature:

 

 

 

 

a. Installed in direct sun.

 

 

 

 

 

 

b.

Poor ventilation.

 

 

 

 

 

 

 

c.

Low voltage.

 

 

 

 

 

 

 

d. Wiring is incorrect size for load.

D.

MOTOR WILL

1.

Check that all power switches are on, fuse not blown, and circuit breaker

 

NOT TURN

 

is not tripped.

 

 

 

 

 

 

2.

Timer improperly set.

 

 

 

 

 

 

3.

Impeller is against volute face.

 

 

 

 

 

SAVE THESE INSTRUCTIONS.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LIMITED

 

 

 

 

 

 

P

WARRANTY P

 

 

 

 

 

 

 

PUMPS

 

 

 

PENTAIR POOL PRODUCTS, INC. pumps are warranted to be free from defects in material and

 

 

 

workmanship. Should any of the operating parts become defective within one year from date of pur-

 

 

 

chase, they will be replaced or repaired if defect is proved to be the responsibility of PENTAIR POOL

 

 

 

PRODUCTS, INC.

 

 

 

 

 

All adjustments are to be based on list prices in effect at the time of adjustment. PENTAIR POOL

 

 

 

PRODUCTS, INC. will not be liable for the cost of labor or removing or replacing parts. Purchase

 

 

 

agrees to prepay all shipping charges to and from PENTAIR POOL PRODUCTS, INC. 1620 Hawkins

 

 

 

Ave., Sanford, NC 27330 or 10951 West Los Angeles Ave., Moorpark, CA 93021, whichever is clos-

 

 

 

er or more convenient.

 

 

 

 

 

 

This warranty does not cover failure in service due to fire, wreckage, freezing, willful abuse, improper repackaging

 

 

 

 

 

 

or damage incurred in shipping nor does it extend to consequential damages.

 

 

 

 

 

 

 

 

 

35-7000

 

 

 

 

 

Printed in the U.S.A.

Rev. B 5/2005

 

 

 

 

 

 

HYDROPUMP®

AND

ENERGY MASTER™ HYDROPUMP®

TWO SPEED POOL AND SPA PUMP

INSTALLATION, OPERATION

& SERVICE MANUAL

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Not Prime Pump willLOW Flow MotorTable of A.W.G. Wire Size For SINGLE-PHASE Pool Pump Motors InstallationMaintenance List of Material or Parts ListSpecial Instruction for TWO Speed Energy Master Hydropump Timer Installation for HI-LO Switching of 2 Speed HydropumpOperating Instructions Impeller Clearance Adjustment

Hydropump, Energy Master specifications

Pentair Energy Master Hydropump is a cutting-edge innovation in the field of water management, designed to efficiently handle the challenges of fluid conveyance and pressure management in various applications. This advanced pumping system is specifically engineered to optimize performance, reduce energy consumption, and provide long-lasting reliability.

One of the standout features of the Energy Master Hydropump is its ability to adapt to the varying demands of different operational contexts. With its intelligent control technology, the pump can automatically adjust its speed and output based on real-time flow requirements. This not only ensures optimal efficiency but also significantly reduces energy costs. The energy-saving capabilities are further enhanced by the use of high-efficiency motors that minimize waste and maximize output.

The Hydropump employs advanced materials in its construction, which contribute to its durability and resistance to wear and corrosion. This makes the pump ideal for use in harsh environments where traditional pumps may fail. Additionally, the hydraulic design of the Energy Master Hydropump minimizes turbulence, leading to quieter operation and reduced vibration, thereby prolonging the lifespan of the equipment.

Ease of installation and maintenance is another key characteristic of the Pentair Energy Master Hydropump. Its user-friendly design allows for straightforward setup, while the modular components facilitate quick and easy servicing. The integration of digital monitoring systems enables real-time diagnostics, allowing for proactive maintenance and reduced downtime.

Versatility is a hallmark of the Energy Master Hydropump, making it suitable for a wide range of applications. Whether in industrial settings, agricultural endeavors, or municipal water systems, this hydropump can meet diverse pumping needs. Furthermore, its scalability means that it can be deployed in small systems or configured for large-scale operations without compromising performance.

In summary, the Pentair Energy Master Hydropump stands out in the market for its efficiency, durability, and versatility. Its intelligent control systems, high-quality materials, and ease of maintenance position it as a superior choice for those seeking reliable water management solutions. With its incorporation of cutting-edge technologies, the Energy Master Hydropump not only fulfills current needs but also sets the stage for future advancements in pumping technology.
Top Page Image Contents