Storage

MAINTENANCE INSTRUCTIONS (continued)

Your mower represents an investment from which you should get the greatest possible benefit and use. Therefore, when the cutting season is over, the mower should be thoroughly checked and prepared for storage so that a minimum amount of work will be required to put it back into operation for the next season.

We suggest the following storage procedures:

1.Thoroughly clean the mower

2.Lubricate the mower as recommended in the mainte- nance section of this manual.

3.Tighten all bolts and pins to the recommended torque.

4.Check the mower for worn or damaged parts and replace any require so.

5.Store the mower in a clean, dry place with the deck resting on blocks.

6.Use spray touch up enamel where necessary to pre- vent rust and maintain its appearance.

BLADE SPINDLE SERVICE INSTRUCTIONS DISASSEMBLY

(See figure 15)

1.Bend tab of lockwasher (item 7) out of the slot in the nut (item 8).

2.Remove the nut (item 8) from spindle shaft (item 3).

3.Support the spindle housing (item 1) and press the spindle (item 3) out of the housing.

4.Remove the bearings (item 2) and the spacer (item 5).

BLADE SPINDLE SERVICE INSTRUCTIONS ASSEMBLY

1.Inspect all parts for damage or wear and make sure that the bearings are in good condition. Replace any parts that show wear or any damage.

2.Clean all components and make sure that they are free of dirt, grease or any other contaminants.

3.Before assembly pack the ball bearings with quality bearing grease.

4.Press a bearing into the housing on the side that has the grease overfill hole. Make sure that the bearing’s dirt seal is facing to the outside of the housing.

5.Install a flat washer (item 6), and the dust cap (item 4). Next press the spindle shaft through the already installed bearing and be certain that the bearing is seated properly.

6.Install the spacer (item 5) on the spindle shaft. Press the second bearing into the opposite side of the housing and make sure that it is properly seated, with the dirt seal facing outside.

7.Next install the flat washer (item 6) and key (item 10) on the shaft. Mount the proper sheave that corre- sponds with the spindle.

8.Install lockwasher (item 7) and nut (item 8) on the shaft and tighten to approximately 65 ft. lb. torque.

9.Align the slot in the nut with the lockwasher tab. Bend the tab into the nut so it locks in place.

10.Grease the spindle assembly through the grease fit- ting (item 9) until a small amount of grease comes out of the relief hole in the housing.

Figure 15

FM 560, FM 572 specifications

The Worksaver FM 560 and FM 572 are advanced agricultural implements designed to enhance efficiency and productivity in various farming operations. These machines are pivotal in delivering superior soil management and cultivation results, catering to the evolving needs of modern agriculture.

The FM 560 is engineered with a working width of 5.6 meters, while the FM 572 boasts an impressive 5.72 meters. Both models feature robust construction, ensuring durability and reliability even in challenging conditions. Built from high-strength materials, these implements can withstand the rigors of intensive farming practices.

One of the standout features of the Worksaver FM series is its adjustable working depth capabilities. Operators can easily set the depth to suit specific soil conditions and crops, allowing for tailored cultivation. This flexibility not only maximizes soil health but also optimizes crop yield. The active tilting mechanism on these models ensures that the implement maintains its position and effectiveness, even on uneven terrain, providing consistent results across fields.

Technologically, the Worksaver FM 560 and FM 572 are equipped with advanced hydraulic systems, enabling smooth operation and quick adjustments in the field. The hydraulic folding system simplifies transport, allowing for easy movement between fields without the need for time-consuming detachment. Additionally, the series includes a variety of interchangeable tines and share options, enabling farmers to customize their setup according to crop and soil type.

Safety is a critical aspect of the design, with features such as a safety shield and automatic overload protection ensuring the well-being of operators and equipment. The FM series also emphasizes ease of maintenance, with accessible components and straightforward servicing procedures, minimizing downtime and enhancing productivity.

In summary, the Worksaver FM 560 and FM 572 are exemplary tools in precision farming, blending innovative technology with practical features to meet contemporary agricultural demands. With their robust build, adjustable settings, and user-friendly operation, these models are ideal choices for farmers seeking to improve soil cultivation and achieve greater yields. The Worksaver FM series represents a commitment to quality and performance, making them invaluable assets in any modern farming operation.