Crown Audio I-T9000 HD Amplifier DSP Selection Screen, Amplifier Mode, Input Signal Level Meter

Page 27

I-Tech HD Series Power Amplifiers

4 Advanced Operation

4.8.1 Amplifier DSP Selection Screen

On the left of this screen is the Input Signal Level Monitor (explained later on this page). On the right side are rows of DSP selection buttons for each channel. When you click on a button, a control panel opens for that button’s function.

Also on the right are buttons that open control panels for these functions:

Amplifi er mode (dual, bridge-mono, input Y)

Signal generator (pink noise and sine wave)

Amplifi er information

Recall and store presets

Preset manager

Apply to others (apply this amplifi er’s DSP settings to other devices)

We’ll explain each of these functions on the next several pages.

4.8.2 Amplifier Mode

This is switchable between dual, bridge-mono and 1x2 (input Y).

Operation Manual

4.8.3 Input Level, Mute, Link, Level Meters, and Indicators

This panel is on the left side of the I-Tech main control panel shown above. Channel 1 and 2 Level Controls set the input signal level of each channel. Each channel can be muted, and both faders can be linked with the Link button.

Input Signal Level Meter

The measurement range is from 0dBFS to –40dBFS with 0.5dB resolution. Each audio channel has the following monitors:

Switched Audio Input: This meter shows only the switched (selected) audio input after the Input Audio Router.

Clip Indicator

Output Signal Level Meter

The measurement range is from 0 dB to –40 dB with 0.5 dB resolution. The monitors are scaled so that 0 dB is referenced to the full rated output voltage of the amplifi er. The left meter is rms and the right meter is peak. An output clip indicator is provided.

Indicators

Temp: Lights if the temperature of the amplifi er is too high and the amplifi er is near shutdown.

Green: Thermal headroom used up is less than 59%.

Yellow: Thermal headroom used up is 60-80%.

Red: Thermal headroom used up is more than 81%.

Limit: Lights when the amplifi er signal is being limited.

Load: Lights when the load impedance is out of range.

Ready: Lights when the amplifi er is on and ready to supply power.

page 27

Image 27
Contents 140811-1 T5000 HDT9000 HD T12000 HD Some models may be exported under the name AmcronWichtige Sicherheitsinstruktionen Important Safety InstructionsEMC Standards Safety StandardEuropean Representative’s Name and Address Family Name I-Tech HDTable of Contents Welcome T5000HDT9000HD T12000HDMagnetic Field SetupUnpack and Install Your Amplifier You may also stack amps without using a cabinetWire Inputs and Outputs Wiring basics Connecting to AC MainsChoose Input Wire and Connectors Choose Output Wire and ConnectorsDistance Important Turn off the amplifier and unplug its power cord Stereo Mode WiringDisabled Bridge-Mono ModeProtecting Your Speakers Startup ProcedurePrecautions OperationFault Indicator Front Panel Controls and IndicatorsPower Switch USB 2.0 ConnectorDigital Inputs Section Back Panel Controls, Indicators and Connectors FansAnalog Inputs Section Outputs SectionAdvanced Operation PresetsExit Navigating the LCD Control Screen IntroductionMenu Tree Next30.0 dB DB MuteOperation Examples Advanced Menu 96 kHz+15dBu Analog Analog+ + OFF v OFFOFF dB OFF Alert Menu Monitor Menu120 VAC 108.8 HrsNetworking Menu Networking MenuCobranet Menu Cobranet MenuPresets Introduction User PresetsDownloadable Presets File Transfer Via the USB Port How to transfer a file from a USB flash drive to the amplifierThese messages may appear on the LCD screen List of Pop-Up Boxes and DescriptionsSelect Network Card Digital Audio Options AES/EBUNetworking the Amplifier Network TroubleshooterClip Indicator Output Signal Level Meter Amplifier ModeInput Level, Mute, Link, Level Meters, and Indicators Input Signal Level MeterDigital with Analog Override Input Signal RouterDigital with Analog Backup Analog Signal Detect Threshold -100 dB to 0 dBSource Configuration CobraNet Advanced SettingsInput Delay and Driver Delay Input Signal CompressorInput EQ and Output EQ Crossover Filters Transducer Thermal Limiting Average Power LimiterLevelMax Suite Peak Voltage LimiterContinuous Load Monitoring On Enables or disables the load-supervision functionADC DSP DAC Preset Manager Sine On/Off Turns the sine-wave generator on or off Signal GeneratorAES input Limiters Amplifier Cobranet input trim Fixed-Gain Mode in the I-Tech HDAmplifi er’s power switch is off TroubleshootingEthernet link is broken Speakers not connected Open circuit due to speaker failureHz 20 kHz with 0.35% THD SpecificationsDimensions Crosstalk below rated power, 20 Hz to 1 kHzCommon Mode Rejection CMR 20 Hz to 1 kHz AC Line ConnectorTypical Frequency Response 1W ChartsTypical Damping Factor vs. Frequency AC Power Draw and Thermal Dissipation 57.6 91.2 99.8 392 1338 337 Btu/hr Kcal/hr205 177 225 767 66063.6 103.3 111.8 441 1504 379 Per 1A Line Current212 183 213 726 625Advanced Features HiQnet Networks HiQnet control offers many advantagesNetwork Addresses 00-0A-40-00-DC-2F 192.168.0.1IP Router Bundles and Audio Channels Closer Look at CobraNetFast Ethernet 100Base-T Audio SpecsConductor Switched NetworksAppendix B Setting Sensitivity for Best Gain Staging Service Warranty Worldwide Except USA & Canada Items Excluded from this CROWN- WarrantyPurchase Date Crown Audio, IncFax Mishawaka RdThis page Intentionally Left Blank Crown Audio Factory Service Information

I-T9000 HD, I-T12000 HD, IT9000 HD, I-T5000 HD specifications

Crown Audio has established itself as a leader in the audio amplification industry, and its IT series, including the IT9000 HD, I-T9000 HD, I-T5000 HD, and I-T12000 HD, exemplifies this commitment to quality and innovation. These amplifiers are engineered to deliver exceptional audio performance, reliability, and user-friendly operation, making them ideal for a variety of applications, from concert sound to installed audio systems.

The IT9000 HD is a powerhouse that provides robust performance through its high-efficiency design. Featuring advanced Class I technology, it can deliver a staggering output of up to 9000 watts. This model is built with a lightweight, compact chassis that allows for easy installation and portability. The IT9000 HD incorporates Crown’s proprietary DriveCore technology, which combines the amplifier’s driver and output stage into a single chip, significantly increasing efficiency and reducing the overall size of the amplifier.

Next in line, the I-T9000 HD offers similar power output capabilities but adds flexibility with its network connectivity options. This model supports the latest in digital signal processing, allowing users to tailor their audio system with precision. It also features intelligent fan cooling technology that adjusts the fan speed based on heat generation, ensuring optimal performance under varying load conditions.

The I-T5000 HD stands out with its unique ability to deliver a maximum of 5000 watts, making it an ideal choice for smaller venues or mobile applications where power-to-weight ratio is critical. It shares many of the technological advancements of its larger counterparts, including enhanced DSP capabilities and comprehensive monitoring via onboard indicators and remote software control.

Lastly, the I-T12000 HD is the flagship model in this series, capable of an impressive 12000 watts output. It boasts advanced power management features and offers multiple operating modes, including stereo and bridged operation. The I-T12000 HD is designed for the most demanding applications, ensuring ultra-reliable performance and pristine sound quality in even the largest spaces.

All models in the Crown IT series feature a rugged construction for durability, along with intuitive front-panel controls for easy operation. They also include comprehensive network control options, allowing users to manage and monitor their systems remotely via DSI (Digital Signal Interface) and DSP capabilities.

In conclusion, Crown Audio's IT9000 HD, I-T9000 HD, I-T5000 HD, and I-T12000 HD amplifiers represent the pinnacle of amplifier technology, delivering unmatched performance, efficiency, and versatility for a wide range of audio applications. Whether for live events or permanent installations, these amplifiers provide the power and reliability necessary to meet the demands of modern audio environments.