Crown Audio I-T5000 HD, IT9000 HD Speakers not connected Open circuit due to speaker failure

Page 40

I-Tech HD Series Power Amplifiers

5 Troubleshooting

CONDITION: No sound, even though the amp has power. Power LED is on

without fl ashing and the amp is receiving an input signal. Signal indicator is on or fl ashing.

POSSIBLE REASON

• Speakers not connected.

• Open circuit due to speaker failure.

• There is a short on the amplifi er output. First disconnect your speakers from the affected channel(s) one by one to determine if one of the loads is shorted.

• Ready LED is off. Channel has been set to standby mode via the software.

• Amplifi er is in blackout mode. Press or turn an Encoder to reactivate the LCD display.

CONDITION: No input signal. Signal indicator is not fl ashing even though audio is applied, and the channel is ready.

POSSIBLE REASON

• Input signal level is very low.

• Another source is selected or routed.

CONDITION: Data indicator not flash- ing, even though host computer software is active.

POSSIBLE REASON:

Cable between computer and amplifi er is broken or not connected.

Note: Data indicator fl ashes only when the amplifi er is polled for data, or is polled to see whether it is online.

CONDITION: Yellow LINK ACTIVITY indicator in Ethernet connector does not illuminate or flash.

POSSIBLE REASON:

• Ethernet link is broken.

CONDITION: COND indicator is off.

POSSIBLE REASON:

There is only one conductor allowed per network system. This indicator is lit only when the amplifi er is the conductor.

Amplifi er is in blackout mode. Press or turn an Encoder to reactivate the LCD display.

CONDITION: Computer does not communicate with the network devices.

POSSIBLE REASON:

Incorrect wiring. See Section 3.5 letter O on network wiring.

IP Addressing is not done correctly. Use the Network Troubleshooting Wizard in System Architect.

page 40

Operation Manual

Image 40
Contents T5000 HD T9000 HD T12000 HDSome models may be exported under the name Amcron 140811-1Important Safety Instructions Wichtige SicherheitsinstruktionenSafety Standard European Representative’s Name and AddressFamily Name I-Tech HD EMC StandardsTable of Contents T5000HD T9000HDT12000HD WelcomeSetup Unpack and Install Your AmplifierYou may also stack amps without using a cabinet Magnetic FieldConnecting to AC Mains Wire Inputs and Outputs Wiring basicsChoose Output Wire and Connectors Choose Input Wire and ConnectorsDistance Stereo Mode Wiring Important Turn off the amplifier and unplug its power cordBridge-Mono Mode DisabledStartup Procedure PrecautionsOperation Protecting Your SpeakersFront Panel Controls and Indicators Power SwitchUSB 2.0 Connector Fault IndicatorBack Panel Controls, Indicators and Connectors Fans Analog Inputs SectionOutputs Section Digital Inputs SectionPresets Advanced OperationNavigating the LCD Control Screen Introduction Menu TreeNext ExitDB Mute 30.0 dBOperation Examples 96 kHz Advanced MenuAnalog Analog +15dBuOFF v OFF + +OFF dB OFF Monitor Menu 120 VAC108.8 Hrs Alert MenuNetworking Menu Networking MenuCobranet Menu Cobranet MenuUser Presets Presets IntroductionDownloadable Presets How to transfer a file from a USB flash drive to the amplifier File Transfer Via the USB PortList of Pop-Up Boxes and Descriptions These messages may appear on the LCD screenDigital Audio Options AES/EBU Networking the AmplifierNetwork Troubleshooter Select Network CardAmplifier Mode Input Level, Mute, Link, Level Meters, and IndicatorsInput Signal Level Meter Clip Indicator Output Signal Level MeterInput Signal Router Digital with Analog BackupAnalog Signal Detect Threshold -100 dB to 0 dB Digital with Analog OverrideCobraNet Advanced Settings Source ConfigurationInput Signal Compressor Input Delay and Driver DelayInput EQ and Output EQ Crossover Filters Average Power Limiter LevelMax SuitePeak Voltage Limiter Transducer Thermal LimitingOn Enables or disables the load-supervision function Continuous Load MonitoringADC DSP DAC Preset Manager Signal Generator Sine On/Off Turns the sine-wave generator on or offFixed-Gain Mode in the I-Tech HD AES input Limiters Amplifier Cobranet input trimTroubleshooting Amplifi er’s power switch is offSpeakers not connected Open circuit due to speaker failure Ethernet link is brokenSpecifications Hz 20 kHz with 0.35% THDCrosstalk below rated power, 20 Hz to 1 kHz Common Mode Rejection CMR 20 Hz to 1 kHzAC Line Connector DimensionsCharts Typical Frequency Response 1WTypical Damping Factor vs. Frequency AC Power Draw and Thermal Dissipation Btu/hr Kcal/hr 205 177225 767 660 57.6 91.2 99.8 392 1338 337Per 1A Line Current 212 183213 726 625 63.6 103.3 111.8 441 1504 379Advanced Features HiQnet control offers many advantages HiQnet NetworksNetwork Addresses 192.168.0.1 00-0A-40-00-DC-2FIP Router Closer Look at CobraNet Fast Ethernet 100Base-TAudio Specs Bundles and Audio ChannelsSwitched Networks ConductorAppendix B Setting Sensitivity for Best Gain Staging Service Warranty Items Excluded from this CROWN- Warranty Worldwide Except USA & CanadaCrown Audio, Inc FaxMishawaka Rd Purchase DateThis page Intentionally Left Blank Crown Audio Factory Service Information

I-T9000 HD, I-T12000 HD, IT9000 HD, I-T5000 HD specifications

Crown Audio has established itself as a leader in the audio amplification industry, and its IT series, including the IT9000 HD, I-T9000 HD, I-T5000 HD, and I-T12000 HD, exemplifies this commitment to quality and innovation. These amplifiers are engineered to deliver exceptional audio performance, reliability, and user-friendly operation, making them ideal for a variety of applications, from concert sound to installed audio systems.

The IT9000 HD is a powerhouse that provides robust performance through its high-efficiency design. Featuring advanced Class I technology, it can deliver a staggering output of up to 9000 watts. This model is built with a lightweight, compact chassis that allows for easy installation and portability. The IT9000 HD incorporates Crown’s proprietary DriveCore technology, which combines the amplifier’s driver and output stage into a single chip, significantly increasing efficiency and reducing the overall size of the amplifier.

Next in line, the I-T9000 HD offers similar power output capabilities but adds flexibility with its network connectivity options. This model supports the latest in digital signal processing, allowing users to tailor their audio system with precision. It also features intelligent fan cooling technology that adjusts the fan speed based on heat generation, ensuring optimal performance under varying load conditions.

The I-T5000 HD stands out with its unique ability to deliver a maximum of 5000 watts, making it an ideal choice for smaller venues or mobile applications where power-to-weight ratio is critical. It shares many of the technological advancements of its larger counterparts, including enhanced DSP capabilities and comprehensive monitoring via onboard indicators and remote software control.

Lastly, the I-T12000 HD is the flagship model in this series, capable of an impressive 12000 watts output. It boasts advanced power management features and offers multiple operating modes, including stereo and bridged operation. The I-T12000 HD is designed for the most demanding applications, ensuring ultra-reliable performance and pristine sound quality in even the largest spaces.

All models in the Crown IT series feature a rugged construction for durability, along with intuitive front-panel controls for easy operation. They also include comprehensive network control options, allowing users to manage and monitor their systems remotely via DSI (Digital Signal Interface) and DSP capabilities.

In conclusion, Crown Audio's IT9000 HD, I-T9000 HD, I-T5000 HD, and I-T12000 HD amplifiers represent the pinnacle of amplifier technology, delivering unmatched performance, efficiency, and versatility for a wide range of audio applications. Whether for live events or permanent installations, these amplifiers provide the power and reliability necessary to meet the demands of modern audio environments.