Blower Sizing, Water Jet Applications | AquaPRO PRO150120 guide

Blower Sizing

Water Jet

Applications

New Spa

Applications

Winterizing

Wiring Guidelines

Installation

5.Verify plumbing is free of leaks before adding water to spa.

Operating Instructions and Parts Manual

PRO1002403, PRO1502403, PRO2002403, PRO100120, PRO150120, and PRO200120

Hartford Loop required if Blower is more than 25 feet away from pool / spa

Alternate location for check valve if Harford Loop is used

Grade

12 inch minimum

5 Foot minimum from water (use non-metallic plumbing)

Conduit box and cover

Non-metallic electrical tubing

24 inches above surrounding grade / 12 inch minimum above water

Orient blower housing as shown

Bracket

Wall or post

Check valve (location when NOT using a Hartford Loop)

Rigid PVC pipe

The number of holes in the seats and floor of the spa can be used to determine the size of the air blower that will be required for your application. See Chart 1 for recommended blower size based on the number and size of holes.

The blower can be used to boost the output of hydrotherapy jets. A venturi fitting is normally incorporated into the jet design. The purpose of the fitting is to allow air to mix with the water in the jet. The venturi fittings

It is important to select a water pump that will supply sufficient flow to the jets. Consult with the jet manufacturer for assistance in selecting a pump or pumps that will accommodate the number of jets desired in the spa. Improper sizing can cause overheating of the pump and blower.

Choose the correct size blower based on the number of water jets in your spa (see Chart 1). See the chart below. Refer to the installation guidelines for additional details.

The blower is designed for outdoor use. There are no special off-season requirements for the blower. In some spa systems it is possible to protect discharge lines from freezing by operating the blower for several minutes with the spa drained. The airflow can be used to purge water from the air lines.

Air flow

Mount using rigid PVC pipe. For additional support, use supplied bracket as shown.

Figure 1

can be connected together and then pressurized with air from the blower to greatly increase the jet action.

		Recommended Number of Holes
Blower	Total Hole Area	at the Following Hole Diameters			Number of
Model	Square Inches	1/8 Inch	3/16 Inch	1/4 Inch	Water Jets

Guidelines (Continued)

Do not glue the blower to the

supply line. Glue fumes can potentially cause an explosion when the blower starts. Install a 1/4” self-tapping screw to secure the joint if necessary.

Do not install blower below

water level. Blower must be at least one foot above the maximum water level.

4.Mount blower in a vertical position using vertical rigid PVC pipe as shown in Figure 1. For additional support use supplied bracket as shown in Figure 1. For warm climates, try to locate the blower in a shaded location.

If the blower is to be installed more

than 25 ft from the spa, it will be necessary to install a loop that is 1 foot above the water line and as close to the spa as possible (See Figure 1).

A loop and a check valve must be

installed at least one foot above the water level when supercharging water jets.

6.Do NOT install adjustable jets. Adjustable jets can cause excessive back pressure within the unit.

7.Hydrotherapy jets naturally aerate when installed correctly. Do not use blower to supplement aeration when jets have been installed incorrectly.

PRO100120, PRO1002403

PRO150120, PRO1502403

PRO200120, PRO2002403

Failure to observe wiring instructions,

could result in death or serious injury.

All wiring and electrical

connections must be performed by a qualified electrician. Installations must be in accordance with local and national codes.

1.For electrical ratings, see product decal.

2.Check the line voltage to make certain it is correct for the blower being used. Do not attempt to connect 240 VAC to a 120-volt blower; it will damage the blower and void the warranty.

3.Refer to the National Electric Code Guidelines for wire size and to prevent electric shock.

4.Refer to the National Electric Code Guidelines for proper selection of wiring conduit and strain relief.

5.The blower field-wiring box is designed for non-metallic electrical tubing only. Refer to the National Electric Code Guidelines for proper selection of wiring, and strain relief.

6.Be certain to connect the green ground wire supplied with the blower to the ground from your electrical panel.

7.Connect remaining line wires individually to the remaining wires in the blower.

8.When wiring is complete carefully install gasket and conduit cover plate.

Overheating, short- circuiting and fire

damage will result from inadequate wiring.

Notes

877.278.2797

www.aquaprosystems.com

877.278.2797