Crown Audio MA-2402 Setup, Unpack Your Amplifier Install Your Amplifier, 48.3 cm, 40.6 cm 35 cm

Page 6

MA 2402 Power Amplifier

3 Setup

3.1 Unpack Your Amplifier

3.2 Install Your Amplifier

3.3 Ensure Proper Cooling

Please unpack and inspect your amplifier for any damage that may have occurred during transit. If damage is found, notify the transportation company immediately. Only you can initiate a claim for ship- ping damage. Crown will be happy to help as needed. Save the shipping carton as evidence of damage for the shipper’s inspection.

We also recommend that you save all packing mate- rials so you will have them if you ever need to trans- port the unit. Never ship the unit without the factory pack.

YOU WILL NEED (not supplied):

Input wiring cables

Output wiring cables

Rack for mounting amplifier (or a stable surface for stacking)

WARNING: Before you start to set up your amplifier, make sure you read and observe the Important Safety Instructions at the beginning of this manual.

CAUTION: Before you begin, make sure your amplifier is disconnected from the power source, with power switch in the “off” posi- tion and all level controls turned completely down (counterclockwise).

Use a standard 19-inch (48.3-cm) equipment rack. See Figure 3.1 for amplifier dimensions.

You may also stack amps without using a cabinet.

NOTE: When transporting, amplifiers should be supported at both front and back.

When using an equipment rack, mount units directly on top of each other. Close any open spaces in rack with blank panels. DO NOT block front or rear air vents. The side walls of the rack should be a minimum of 2 inches (5.1 cm) away from the ampli- fier sides, and the back of the rack should be a min- imum of 4 inches (10.2 cm) from the amplifier back panel.

Figure 3.2 illustrates standard amplifier airflow.

 

LEVEL

 

 

 

LEVEL

 

12

15

 

 

12

15

 

18

 

ODEP

18

 

9

21

 

9

21

 

 

 

 

 

 

 

ON

6

24

 

SIGNAL / IOC

6

24

OFF

 

 

 

 

 

 

 

 

 

 

3.5 in

3

27

 

 

3

27

0

30

CH1

CH2

0

30

ENABLE

 

 

 

 

 

 

8.9 cm

19 in

48.3 cm

Figure 3.2 Airflow

SIDE VIEW

16 in

2.5 in

40.6 cm

6.35 cm

Figure 3.1 Dimensions

page 6

Operation Manual

Image 6
Contents Macro-Tech Some models may be exported under the name AmcronImportant Safety Instructions Importantes Instructions de SécuritéTCF Technical Certificate No P4300CRI1.IWS Safety StandardCrown Audio, Inc Competent Body’s Name and AddressTable of Contents How to Use This Manual FeaturesWelcome You may also stack amps without using a cabinet SetupUnpack Your Amplifier Install Your Amplifier 48.3 cmChoose Input Wire Connectors Choose Output Wire and Con- nectorsSee .6. Set the back panel stereo/mono switch to Stereo Wire Your SystemStereo Mode Bridge-Mono ModeParallel-Mono Mode Operation Startup ProcedurePrecautions Set Input SensitivityOdep Indicators Front Panel Controls and IndicatorsSignal/IOC Indicators Enable IndicatorReset Switches Back Panel Controls, Indicators and Connec Tors Power CordStereo/Mono Switch Input Sensitivity Switch not shownIndicators IndicatorsProtection Systems Advanced Features OptionsStandby Mode OdepAdvanced Features Here are some of its many featuresFuses and Circuit Breakers Options PIP and PIP2 Modules PIP2 Adapter ConnectionCooling Fan Options Level Control Shaft LockTroubleshooting Overview Please refer to the block diagram in FigureTheory of Operation Circuit TheoryBridge-Mono Operation Parallel-Mono OperationSpecifications 120 VAC, 60 Hz Units, Bridge mono mode120 VAC, 60 Hz Units, Parallel mono mode Weight Net Weight Power Draw at IdleDimensions Width Shipping WeightMaximum Power Notes Macro-Tech 2402 Maximum Power MatrixMinimum Power Notes Macro-Tech 2402 Minimum Power MatrixAC Power Draw and Thermal Dissipation Constant 0.35 is inefficiency 1.00-0.65AC Power Draw Thermal Dissipation Service Warranty United States & CanadaReason for failure, except as excluded in this Warranty 12/01MA 2402 Power Amplifier Crown Audio, Inc FaxMishawaka Rd Elkhart This page Intentionally Left Blank Model ‰ Personal/Consumer ‰ Business/CorporateMA 2402 Power Amplifier MA 2402 Power Amplifier