Subaru Robin Power Products R1700i service manual Pulsar coil and grommet, Blower housing

Page 32

5-4-7 Pulsar coil and grommet

Tighten the bolt in place, making adjustments according

to 5-4-6.

M6 x 8mm Flange bolt : 2pcs.

Tightening torque : 3.0-5.0 N・m

30-50 kgf・cm

(2.2-3.7 ft・lbs)

Place the pulsar coil wires along the groove of the grommet and recoil guide to make it easier to assemble the blower housing.

Caution : Do not forget to put the 2 pieces of pipe knock.

Recoil guide	Pulsar coil
Flywheel	Grommet
Flywheel
	Pulsar coil harness

5-4-8 Blower housing

Install the blower housing

M8 x 55mm Flange bolt : 1pce.

M8 x 90mm Flange bolt : 3pcs.

Tightening torque : 18.0-20.0 N・m 180-200 kgf・cm (13.3-14.8 ft・lbs)

NOTE: Insert the grommet (pulsar coil harness) and recoil guide into the blower housing securely.

Blower housing

– 29 –

Image 32

Contents Generator Page Contents Specifications R1700iGeneral Description External ViewEngine Switch Control PanelOIL Sensor Lamp AC Receptacles Generator Assembly Range of Applications Incandescent lamp, heater, etc. with a power factorMercury lamps with a smaller power factor Appliances without any indication as to power consumption WattageCross Allowable Cable Voltage drops per 30 meters of cable Measuring and Checking Procedures InstrumentsCircuit Tester Dr.Robin Dr.RobinPartNumber388-47565-08AC Output Measuring Measuring Insulation ResistanceAlternator Checking Functional Members （1）STATORDiode Rectifier Below the lower level on continuity Oil capacity 0.4 litersSpecial Tools Assembly and DisassemblyPrecautions Disassembly Procedures Remove rolling wire, choke wireRemove the side panels Left, Right Remove the rear coverRemove the recoil starter handle Remove the control panelRemove the case body Left, Right Upper part of the case bodyRemove the fuel tank Remove rear frameRemove fuel cock bracket Remove the inverter unit Remove the fuel pipesRemove the base inverter Remove the air cleaner and carburetorRemove the front frame Remove the Stator / Rear cover Remove the rotorRemove recoil starter Remove Blower housingRemove the flywheel Remove the cylinder baffle Remove the mufflerRemove the ignition coil Reassembly Procedures Air gap 0.5 mm Air gap adjustment of flywheel and pulsar coilRecoil starter Tightening torque 3.0-5.0 N・m 30-50 kgf・cm 3.7 ft・lbs Blower housingPulsar coil and grommet Rotor Rear cover, statorAir cleaner bottom plate and carburetor Base InverterTightening torque 90-110 Kgf ・cm 8.1 Ft ・lbs Front frameInstalling coupler Fuel pipeInverter unit Tightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbsFuel tank Fuel cock bracketCase body, control panel Choke wire and rolling wire Rear coverDisassembly procedures Recoil StarterDisassembly is completed Assembly procedure About 20cm Fixed hole Rope Cut of the reel Pull off hole Checking items after assembly When Troubleshooting No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Wiring Diagram R1700i 50Hz-230VR1700i 50Hz-240V R1700i 60Hz-120V Page Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax

R1700i specifications

The Subaru Robin Power Products R1700i is a high-performance inverter generator designed to provide reliable and efficient power for both recreational and professional use. It is particularly popular among outdoor enthusiasts, campers, and contractors due to its compact size, lightweight nature, and advanced technologies.

One of the most notable features of the R1700i is its inverter technology. This allows the generator to produce clean, stable power with a low total harmonic distortion (THD), which is crucial for sensitive electronics such as laptops, smartphones, and communication devices. The inverter system ensures that the power output remains consistent, adapting to the load demand to deliver the exact amount of power required, enhancing fuel efficiency and extending runtime.

The R1700i is equipped with a powerful Subaru engine that delivers reliable performance with a maximum output of 1,700 watts. The engine is designed for durability and longevity, making it capable of handling various power needs. Its efficient design ensures that users can enjoy longer operation times on a single tank of fuel, which is a critical advantage for those who need extended power for their activities.

Another key characteristic of the R1700i is its lightweight and portable design. Weighing only around 37 pounds, it can be easily transported, making it ideal for camping trips, tailgating, or construction sites where mobility is essential. The generator features a sturdy handle for easy lifting and maneuvering, as well as a compact footprint that allows it to fit in tight spaces.

The Subaru Robin R1700i also includes several user-friendly features, such as an easy-start system, an eco-mode for enhanced fuel efficiency, and a quiet operation that minimizes noise pollution. It operates at a relatively low noise level, making it suitable for environments where quiet is necessary, such as during outdoor gatherings or in residential areas.

Safety is also a priority with the R1700i, as it comes with built-in protection features, including overload protection and low oil alert, ensuring that users can operate the generator with peace of mind.

In summary, the Subaru Robin Power Products R1700i combines power, portability, and advanced technology, making it an excellent choice for anyone in need of a reliable and efficient inverter generator. Its blend of features makes it suitable for a wide array of applications, providing users with the confidence to tackle various power challenges while enjoying the great outdoors or completing essential tasks.