Subaru Robin Power Products R1700i Base Inverter, Tightening torque 90-110 Kgf ・cm 8.1 Ft ・lbs

Page 34

5-4-11 Base Inverter

Install the base inverter into the engine main body. M8 x 20 Bolt and washer : 4pcs.

Tightening torque : 18.0-20.0 N・m 180-200 kgf・cm (13.3-14.8 ft・lbs)

M6 Flange nut : 4pcs.

Tightening torque : 9.0-11.0

N・m

90-110

kgf・cm

(6.6-8.1

ft・lbs)

 

 

NOTE: Avoid cutting your hand by the sharp edge of

the base.

5-4-12 Front frame

Install the front frame (L) and (R) onto the base inverter.

5-4-13 Air cleaner bottom plate and carburetor

Install the insulator,gaskets, carburetor, baffle stay, and air cleaner base plate into the cylinder head.

M6 Flange nut : 2pcs.

Tightening torque : 7.0-9.0 N・m

70-90 kgf・cm

(5.2-6.6 ft・lbs)

NOTE: Please do not forget to install the gasket.

5-4-14 Air cleaner

Install the element and air cleaner cover onto the air cleaner base plate.

M6 x 18mm Flange bolt : 1pce.

Base inverter

Front frame

Carburetor

Air cleaner base plate

Air cleaner

– 31 –

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Generator Page Contents Specifications R1700iGeneral Description External ViewEngine Switch Control PanelOIL Sensor Lamp AC Receptacles Generator Assembly Mercury lamps with a smaller power factor Incandescent lamp, heater, etc. with a power factorRange of Applications Appliances without any indication as to power consumption WattageCross Allowable Cable Voltage drops per 30 meters of cable Measuring and Checking Procedures InstrumentsCircuit Tester Dr.Robin Dr.RobinPartNumber388-47565-08AC Output Measuring Measuring Insulation ResistanceAlternator Checking Functional Members （1）STATORDiode Rectifier Below the lower level on continuity Oil capacity 0.4 litersPrecautions Assembly and DisassemblySpecial Tools Remove the side panels Left, Right Disassembly ProceduresRemove rolling wire, choke wire Remove the rear coverRemove the case body Left, Right Remove the recoil starter handleRemove the control panel Upper part of the case bodyRemove fuel cock bracket Remove rear frameRemove the fuel tank Remove the inverter unit Remove the fuel pipesRemove the front frame Remove the air cleaner and carburetorRemove the base inverter Remove the Stator / Rear cover Remove the rotorRemove the flywheel Remove Blower housingRemove recoil starter Remove the ignition coil Remove the mufflerRemove the cylinder baffle Reassembly Procedures Recoil starter Air gap adjustment of flywheel and pulsar coilAir gap 0.5 mm Pulsar coil and grommet Blower housingTightening torque 3.0-5.0 N・m 30-50 kgf・cm 3.7 ft・lbs Rotor Rear cover, statorTightening torque 90-110 Kgf ・cm 8.1 Ft ・lbs Air cleaner bottom plate and carburetorBase Inverter Front frameInverter unit Installing couplerFuel pipe Tightening torque 3.0-4.0 N・m 30-40 kgf・cm 2.2-2.9 ft・lbsFuel tank Fuel cock bracketCase body, control panel Choke wire and rolling wire Rear coverDisassembly procedures Recoil StarterDisassembly is completed Assembly procedure About 20cm Fixed hole Rope Cut of the reel Pull off hole Checking items after assembly When Troubleshooting No output power or Lower outputImproper revolutions Electronic throttle Engine does not start Start failure Wiring Diagram R1700i 50Hz-230VR1700i 50Hz-240V R1700i 60Hz-120V Page Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax

R1700i specifications

The Subaru Robin Power Products R1700i is a high-performance inverter generator designed to provide reliable and efficient power for both recreational and professional use. It is particularly popular among outdoor enthusiasts, campers, and contractors due to its compact size, lightweight nature, and advanced technologies.

One of the most notable features of the R1700i is its inverter technology. This allows the generator to produce clean, stable power with a low total harmonic distortion (THD), which is crucial for sensitive electronics such as laptops, smartphones, and communication devices. The inverter system ensures that the power output remains consistent, adapting to the load demand to deliver the exact amount of power required, enhancing fuel efficiency and extending runtime.

The R1700i is equipped with a powerful Subaru engine that delivers reliable performance with a maximum output of 1,700 watts. The engine is designed for durability and longevity, making it capable of handling various power needs. Its efficient design ensures that users can enjoy longer operation times on a single tank of fuel, which is a critical advantage for those who need extended power for their activities.

Another key characteristic of the R1700i is its lightweight and portable design. Weighing only around 37 pounds, it can be easily transported, making it ideal for camping trips, tailgating, or construction sites where mobility is essential. The generator features a sturdy handle for easy lifting and maneuvering, as well as a compact footprint that allows it to fit in tight spaces.

The Subaru Robin R1700i also includes several user-friendly features, such as an easy-start system, an eco-mode for enhanced fuel efficiency, and a quiet operation that minimizes noise pollution. It operates at a relatively low noise level, making it suitable for environments where quiet is necessary, such as during outdoor gatherings or in residential areas.

Safety is also a priority with the R1700i, as it comes with built-in protection features, including overload protection and low oil alert, ensuring that users can operate the generator with peace of mind.

In summary, the Subaru Robin Power Products R1700i combines power, portability, and advanced technology, making it an excellent choice for anyone in need of a reliable and efficient inverter generator. Its blend of features makes it suitable for a wide array of applications, providing users with the confidence to tackle various power challenges while enjoying the great outdoors or completing essential tasks.
Top Page Image Contents