Baldor manual Product Safety Information MN2412

Page 10

Caution Statements

Caution: The brass connecting tab on some 120VAC duplex receptacles have been removed. Each receptacle is powered by a separate generator winding. When replacing a receptacle, inspect the brass tab that normally links both receptacles. If it is removed, be sure to remove the brass tab from the replacement receptacle before it is installed. Failure to remove the tab will cause a direct short to the generator windings and cause possible generator damage.

Caution: Avoid installing the generator set beside heat generating equipment, or directly below water or steam pipes or in the vicinity of corrosive substances or vapors, metal particles and dust. Heat can cause engine problems to develop and unwanted substances can cause rust or generator failure over time.

Caution: Do not apply high voltage to windings in a moisture–saturated condition. Moisture can cause insulation breakdown, making it necessary to return the generator to the factory for repair, and consequent expense and loss of time.

Caution: Use only original equipment or authorized replacement parts. Using the correct parts will assure continued safe operation as designed.

Caution: Do not support the generator from the top of the wrap frame.

Caution: Do not tamper with or change the engine speed. Engine speed is factory set to produce the correct voltage and output frequency.

Caution: Never operate the engine without a muffler. The engine is designed to have the correct exhaust components installed and operating without these components can present a fire hazard, cause excessive exhaust gases and cause damage to engine. Inspect muffler periodically and replace if necessary.

Caution: Operate the generator only on a level surface. Operation of the generator on an incline or slope may degrade engine lubrication and result in engine failure.

Caution: Always fill fuel tank with clean fresh fuel before use. Never leave fuel in tank for long storage periods. Old fuel becomes stale and can damage the fuel system causing the engine not to start. Always drain the fuel tank after use before storage.

Caution: For electric start models, do not place the key switch in the start position when engine is running. This causes the starting motor to engauge and may damage the starter and engine.

1-6 Product Safety Information

MN2412

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PowerchiefR POW’R Products Generator California Proposition 65 Warning Table of Contents Ii Table of Contents MN2412 Section Product Safety Information Read This Manual ThoroughlyProperty Precaution Statements Used In This ManualOperation Operation Warning Statements Burn Installation Maintenance Product Safety Information MN2412 Warranty Period Generator Series Labor Parts Limited WarrantySection General Information General Information MN2412 Section Receiving & Installation PowerchiefR Generators StoragePhysical Location Receptacle Connections Frame Ground ConnectionEngine Oil Battery Connections Use of Electric Motor LoadsRecommended Engine Oil and Battery Type Series PCSection Operation Operator Control PanelStopping Procedure Start-Up Procedure Electric StartRecoil Start General Section Troubleshooting and MaintenanceEngine Troubleshooting Guide Problems and SolutionsService Appendix a PowerchiefR Series Figure A-1 PC30H Operator PanelReplacement Parts Table A-1 Generator Set Parts ListReceptacle, 125VAC at 15 Amps Figure A-5 PC30H Wiring Diagram Figure A-6 PC40H Wiring Diagram Figure A-7 PC50H Wiring Diagram Figure A-8 PC60H Wiring Diagram Figure A-9 PC90VE Wiring Diagram Baldor District Offices Baldor Generators

MN2412 specifications

The Baldor MN2412 is a premier electric motor known for its high efficiency, rugged construction, and advanced features that cater to various industrial and commercial applications. This motor exemplifies Baldor's commitment to quality, durability, and performance, making it an ideal choice for demanding environments.

One of the most notable characteristics of the MN2412 is its efficiency. Engineered to meet stringent NEMA Premium Efficiency standards, the motor reduces energy consumption, thereby lowering operational costs and contributing to a more sustainable environment. The efficient design minimizes heat generation, allowing the motor to operate at safe temperatures even under heavy loads.

The MN2412 features a robust construction made of high-grade materials that ensure longevity. It is equipped with high-quality bearings that provide excellent load-carrying capabilities and extended service life. The enclosure is typically made of durable cast iron, offering protection against dust and moisture while ensuring the motor can withstand harsh operating conditions.

In terms of technology, the Baldor MN2412 incorporates advanced winding designs that enhance performance and efficiency. The windings are coated for enhanced insulation, which helps to resist electrical shorts and prolong the motor's lifespan. Furthermore, the motor is designed with a removable fan cover, making maintenance and repair tasks straightforward and efficient.

Variety in design is another key feature of the MN2412. It is available in various configurations, including different voltages and horsepower ratings, allowing it to be suitable for a wide range of applications—from pumps and fans to conveyors and compressors. Additionally, the MN2412 supports dual-voltage operation, which provides flexibility in installation, allowing it to operate on different power supply systems.

Another significant advantage of the MN2412 is its low noise level. The engineering team has meticulously designed the motor to minimize vibration and operational noise, making it suitable for environments where noise reduction is essential.

The Baldor MN2412 is also integrated with capabilities for use in variable frequency drive (VFD) applications, enhancing its versatility in speed control and operational efficiency. With its adaptability and high performance, the MN2412 stands out as a reliable choice for industries requiring precision and reliability.

In summary, the Baldor MN2412 electric motor combines efficiency, durability, flexibility, and advanced technology, making it an exceptional choice for a variety of industrial applications. Its design ensures maximum uptime and minimal maintenance, contributing to overall operational success.
Top Page Image Contents