Baldor MN2412 manual Section General Information, Limited Warranty

Page 11

Section 2

General Information

Thank you for purchasing your Baldor Generator Set. This manual contains information you need to safely and efficiently install and operate your generator set. During the preparation of this manual every effort was made to ensure the accuracy of its contents. This manual describes only very basic engine information. A separate owner’s manual for the engine is supplied with this unit for your use. Please refer to the engine manual for information relative to engine operation, maintenance, recommendations and additional safety warnings.

Copyright Baldor 2004. All rights reserved.

This manual is copyrighted and all rights are reserved. This document may not, in whole or in part, be copied or reproduced in any form without the prior written consent of Baldor Electric Company, Inc.

Baldor Generators have earned the reputation of being high quality and dependable. We take pride in this fact and continue to keep our quality standards high on our list of priorities. We are also constantly researching new technological ideas to determine if they could be used to make our generator sets even better.

Baldor makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of fitness for any particular purpose. The information in this document is subject to change without notice. Baldor assumes no responsibility for any errors that may appear in this document.

Limited Warranty

Baldor Generators will replace or repair free of charge any part or parts of the generator of their manufacture that are defective in workmanship and materials for a period of time as set forth in the Warranty Period chart below. All Baldor products requiring warranty service shall be transported or shipped freight pre–paid, at the risk of the party requiring warranty service, to a Baldor Generator repair facility, or to Baldor Generators

Department in Oshkosh, Wisconsin. Written notification of the alleged defect in addition to a description of the manner in which the Baldor generator is used, and the name, address and telephone number of the party requiring warranty service must be included. Baldor is not responsible for removal and shipment of the Baldor product to the service center or for the reinstallation of the Baldor product upon its return to the party requiring warranty service. Problems with Baldor products can be due to improper maintenance, faulty installation, non–Baldor additions or modifications, or other problems not due to defects in Baldor workmanship or materials. If a Baldor Generator repair facility determines that the problem with a Baldor product is not due to defects in Baldor workmanship or materials, then the party requesting warranty service will be responsible for the cost of any necessary repairs.

EXCEPT FOR THE EXPRESSED WARRANTY SET FORTH ABOVE, BALDOR GENERATORS DISCLAIMS ALL OTHER EXPRESSED AND IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. NO OTHER WARRANTY, EXPRESSED OR IMPLIED, WHETHER OR NOT SIMILAR IN NATURE TO ANY OTHER WARRANTY PROVIDED HEREIN, SHALL EXIST WITH RESPECT TO THE GOODS SOLD UNDER THE PROVISIONS OF THESE TERMS AND CONDITIONS. ALL OTHER SUCH WARRANTIES ARE HEREBY EXPRESSLY WAIVED BY THE BUYER. UNDER NO CIRCUMSTANCES SHALL BALDOR GENERATORS BE LIABLE OR RESPONSIBLE IN ANY MANNER WHATSOEVER FOR ANY INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR ANTICIPATED PROFITS RESULTING FROM THE DEFECT, REMOVAL, REINSTALLATION, SHIPMENT OR OTHERWISE. This is the sole warranty of Baldor Generators and no other affirmations or promises made by Baldor Generators shall be deemed to create an expressed or implied warranty. Baldor Generators has not authorized anyone to make any representations or warranties other than the warranty contained herein.

Warranty Period

 

 

 

 

 

Generator Series

Labor*

Parts

Portable Products

1 Year

3 Years

(Premier, Powerchief, DG Series, K Series)

 

 

Towable Products (TS)

1 Year or 3,000 Hours

3 Years or 3,000 Hours

 

Whichever comes first

Whichever comes first

3600 RPM Standby Systems

1 Year or 1,000 Hours

3 Years or 1,000 Hours

(Some AE Models)

Whichever comes first

Whichever comes first

1800 RPM Standby Systems

1 Year or 3,000 Hours

3 Years or 3,000 Hours

(Some AE Models, DLC, GLC)

Whichever comes first

Whichever comes first

Industrial Standby Systems

1 Year or 1,000 Hours

2 Years or 1,000 Hours

 

Whichever comes first

Whichever comes first

Industrial Prime Power Systems

1 Year or 1,000 Hours

1 Year or 1,000 Hours

 

Whichever comes first

Whichever comes first

International

1 Year or 1,000 Hours

1 Year or 1,000 Hours

 

Whichever comes first

Whichever comes first

*For products covered under labor coverage, travel expenses will be allowed up to 7 hours straight labor or 300 miles, whichever occurs first and only applies to permanently wired and mounted products (AE, DLC, GLC, IDLC). No warranty registration card is necessary to obtain warranty on Baldor Generators.

You must save the purchase receipt. Proof of purchase, date, serial number and model number will be required for all portable and Towable products to qualify for any warranty consideration.

For all other products, a start–up inspection form/warranty registration must be completed in its entirety and submitted to Baldor Generators within 30 days of start–up to qualify for any warranty consideration.

MN2412

General Information 2-1

Image 11
Contents PowerchiefR POW’R Products Generator California Proposition 65 Warning Table of Contents Ii Table of Contents MN2412 Read This Manual Thoroughly Section Product Safety InformationOperation Precaution Statements Used In This ManualProperty Operation Warning Statements Burn Installation Maintenance Product Safety Information MN2412 Section General Information Limited WarrantyWarranty Period Generator Series Labor Parts General Information MN2412 PowerchiefR Generators Storage Section Receiving & InstallationPhysical Location Frame Ground Connection Receptacle ConnectionsEngine Oil Use of Electric Motor Loads Battery ConnectionsSeries PC Recommended Engine Oil and Battery TypeOperator Control Panel Section OperationRecoil Start Start-Up Procedure Electric StartStopping Procedure Engine Section Troubleshooting and MaintenanceGeneral Service Problems and SolutionsTroubleshooting Guide Figure A-1 PC30H Operator Panel Appendix a PowerchiefR SeriesTable A-1 Generator Set Parts List Replacement PartsReceptacle, 125VAC at 15 Amps Figure A-5 PC30H Wiring Diagram Figure A-6 PC40H Wiring Diagram Figure A-7 PC50H Wiring Diagram Figure A-8 PC60H Wiring Diagram Figure A-9 PC90VE Wiring Diagram Baldor District Offices Baldor Generators

MN2412 specifications

The Baldor MN2412 is a premier electric motor known for its high efficiency, rugged construction, and advanced features that cater to various industrial and commercial applications. This motor exemplifies Baldor's commitment to quality, durability, and performance, making it an ideal choice for demanding environments.

One of the most notable characteristics of the MN2412 is its efficiency. Engineered to meet stringent NEMA Premium Efficiency standards, the motor reduces energy consumption, thereby lowering operational costs and contributing to a more sustainable environment. The efficient design minimizes heat generation, allowing the motor to operate at safe temperatures even under heavy loads.

The MN2412 features a robust construction made of high-grade materials that ensure longevity. It is equipped with high-quality bearings that provide excellent load-carrying capabilities and extended service life. The enclosure is typically made of durable cast iron, offering protection against dust and moisture while ensuring the motor can withstand harsh operating conditions.

In terms of technology, the Baldor MN2412 incorporates advanced winding designs that enhance performance and efficiency. The windings are coated for enhanced insulation, which helps to resist electrical shorts and prolong the motor's lifespan. Furthermore, the motor is designed with a removable fan cover, making maintenance and repair tasks straightforward and efficient.

Variety in design is another key feature of the MN2412. It is available in various configurations, including different voltages and horsepower ratings, allowing it to be suitable for a wide range of applications—from pumps and fans to conveyors and compressors. Additionally, the MN2412 supports dual-voltage operation, which provides flexibility in installation, allowing it to operate on different power supply systems.

Another significant advantage of the MN2412 is its low noise level. The engineering team has meticulously designed the motor to minimize vibration and operational noise, making it suitable for environments where noise reduction is essential.

The Baldor MN2412 is also integrated with capabilities for use in variable frequency drive (VFD) applications, enhancing its versatility in speed control and operational efficiency. With its adaptability and high performance, the MN2412 stands out as a reliable choice for industries requiring precision and reliability.

In summary, the Baldor MN2412 electric motor combines efficiency, durability, flexibility, and advanced technology, making it an exceptional choice for a variety of industrial applications. Its design ensures maximum uptime and minimal maintenance, contributing to overall operational success.