Baldor MN2412 manual Burn Installation

Page 8

Warning Statements Continued

Burn

WARNING: Parts of this generator are extremely hot during and after operation. To prevent severe burns, do not touch any part of the generator until you have first determined if the part is hot. Wear protective clothing and after use allow sufficient time for parts to cool before touching any part of the generator.

WARNING: Do not touch the hot exhaust parts or the high voltage spark plug or coil terminals of the engine. Although spark plug voltages are not normally lethal, a sudden involuntary jerk of the hand or body part caused by contact with high voltage or a hot surface can result in injury to yourself or others.

Installation

WARNING: Installation and repair procedures requires specialized skills with electrical generating equipment and small engine systems. Any person that installs or performs repairs must have these specialized skills to ensure that the generator set is safe to operate. Contact Baldor for installation or repairs.

WARNING: Be sure all wiring complies with the National Electrical Code (NEC) and all regional and local codes or CE Compliance. Improper wiring may cause a hazardous condition and exposure to electrical hazards can cause serious injury or death.

WARNING: Be sure the system is properly grounded before applying power. Do not apply AC power before you ensure that grounds are connected. Electrical shock can cause serious or fatal injury. NEC requires that the frame and exposed conductive surfaces (metal parts) be connected to an approved earth ground. Local codes may also require proper grounding of generator systems.

WARNING: Place protective covers over all rotating parts such as drive shaft, pulley, belt etc. Rotating parts cause extremely dangerous situations because they can catch loose clothing or extremities and cause serious or fatal injury.

WARNING: Unauthorized modification of a generator set may make the unit unsafe for operation or may impair the operation of the unit. Never start a generator set that has been modified or tampered with. Be sure that all covers and guards are properly installed and that the unit is safe before starting the engine. If you are unsure, contact Baldor before starting the engine.

WARNING: When moving the generator, use reasonable caution. Be careful where you place fingers and toes to prevent injury “Pinch Points”. Never try to lift a generator without a hoist or lift means because they are heavy and bodily injury may result.

WARNING: When transporting a generator (especially if it has wheel option installed) secure the unit to prevent movement during transport.

WARNING: Never connect this generator to any buildings electrical system unless a licensed electrician has installed an approved transfer switch. The National Electrical Code (NEC) requires that connection of a generator to any electrical circuit normally powered by means of an electric utility must be connected by means of approved transfer switch equipment so as to isolate the electrical circuit from the utility distribution system when the generator is operating. Failure to isolate the electrical circuits by such means may result in injury or death to utility power workers due to backfeed of electrical energy onto the utility lines.

WARNING: Circuit overload protection must be provided in accordance with the National Electrical Code and local regulations.

WARNING: Check Ground Fault Circuit Interrupt (GFCI) receptacles monthly by using the “Test” and “Reset” buttons.

WARNING: Only a professional experienced technician should install a fuel supply system. Gasoline and diesel fuel are flammable and can cause fire, explosions, injury or death. Fuel supply lines should be kept away from sharp objects to prevent rupture. Comply with all NFPA regulations and local codes for shut–off valves, regulators, fuel line type etc.

WARNING: Have electrical circuits and wiring installed and checked by licensed electrician or qualified technician. Electrical shock can cause serious or fatal injury.

WARNING: Incorrect installation of this generator set could result in property damage, injury or death. Connection of the generator to its fuel source must be done by a qualified professional technician or contractor.

Continued on next page.

1-4 Product Safety Information

MN2412

Page 7 Page 9
Image 8
Page 7 Page 9
Contents PowerchiefR POW’R Products Generator California Proposition 65 Warning Table of Contents Ii Table of Contents MN2412 Section Product Safety Information Read This Manual ThoroughlyOperation Precaution Statements Used In This ManualProperty Operation Warning Statements Burn Installation Maintenance Product Safety Information MN2412 Section General Information Limited WarrantyWarranty Period Generator Series Labor Parts General Information MN2412 Section Receiving & Installation PowerchiefR Generators StoragePhysical Location Receptacle Connections Frame Ground ConnectionEngine Oil Battery Connections Use of Electric Motor LoadsRecommended Engine Oil and Battery Type Series PCSection Operation Operator Control PanelRecoil Start Start-Up Procedure Electric StartStopping Procedure Engine Section Troubleshooting and MaintenanceGeneral Service Problems and SolutionsTroubleshooting Guide Appendix a PowerchiefR Series Figure A-1 PC30H Operator PanelReplacement Parts Table A-1 Generator Set Parts ListReceptacle, 125VAC at 15 Amps Figure A-5 PC30H Wiring Diagram Figure A-6 PC40H Wiring Diagram Figure A-7 PC50H Wiring Diagram Figure A-8 PC60H Wiring Diagram Figure A-9 PC90VE Wiring Diagram Baldor District Offices Baldor Generators

MN2412 specifications

The Baldor MN2412 is a premier electric motor known for its high efficiency, rugged construction, and advanced features that cater to various industrial and commercial applications. This motor exemplifies Baldor's commitment to quality, durability, and performance, making it an ideal choice for demanding environments.

One of the most notable characteristics of the MN2412 is its efficiency. Engineered to meet stringent NEMA Premium Efficiency standards, the motor reduces energy consumption, thereby lowering operational costs and contributing to a more sustainable environment. The efficient design minimizes heat generation, allowing the motor to operate at safe temperatures even under heavy loads.

The MN2412 features a robust construction made of high-grade materials that ensure longevity. It is equipped with high-quality bearings that provide excellent load-carrying capabilities and extended service life. The enclosure is typically made of durable cast iron, offering protection against dust and moisture while ensuring the motor can withstand harsh operating conditions.

In terms of technology, the Baldor MN2412 incorporates advanced winding designs that enhance performance and efficiency. The windings are coated for enhanced insulation, which helps to resist electrical shorts and prolong the motor's lifespan. Furthermore, the motor is designed with a removable fan cover, making maintenance and repair tasks straightforward and efficient.

Variety in design is another key feature of the MN2412. It is available in various configurations, including different voltages and horsepower ratings, allowing it to be suitable for a wide range of applications—from pumps and fans to conveyors and compressors. Additionally, the MN2412 supports dual-voltage operation, which provides flexibility in installation, allowing it to operate on different power supply systems.

Another significant advantage of the MN2412 is its low noise level. The engineering team has meticulously designed the motor to minimize vibration and operational noise, making it suitable for environments where noise reduction is essential.

The Baldor MN2412 is also integrated with capabilities for use in variable frequency drive (VFD) applications, enhancing its versatility in speed control and operational efficiency. With its adaptability and high performance, the MN2412 stands out as a reliable choice for industries requiring precision and reliability.

In summary, the Baldor MN2412 electric motor combines efficiency, durability, flexibility, and advanced technology, making it an exceptional choice for a variety of industrial applications. Its design ensures maximum uptime and minimal maintenance, contributing to overall operational success.
Top Page Image Contents