Baldor MN2412 manual Section Product Safety Information, Read This Manual Thoroughly

Page 5

Section 1

Product Safety Information

Safety Notice

Be sure that you are completely familiar with the safe operation of this equipment. This

 

equipment may be connected to other machines that have rotating parts or parts that are

 

controlled by this equipment. Improper use can cause serious or fatal injury. Always

 

disconnect all electrical loads before starting the generator.

 

Installation and repair procedures require specialized skills with electrical generating equipment

 

and liquid cooled engine systems. Any person that installs or repairs this generator must have

 

these specialized skills to ensure that this generating unit is safe to operate. Contact Baldor

 

service department for repairs or any questions you may have about the safe installation and

 

operation of this system.

 

The precaution statements are general guidelines for the safe use and operation of this

 

generator. It is not practical to list all unsafe conditions. Therefore, if you use a procedure that is

 

not recommended in this manual you must determine if it is safe for the operator and all

 

personnel in the proximity to the generator and connected loads. If there is any question of the

 

safety of a procedure please contact Baldor before starting the generator.

 

This equipment contains high voltages. Electrical shock can cause serious or fatal injury. Only

 

qualified personnel should attempt the start–up procedure or troubleshoot this equipment.

 

This equipment may be connected to other machines that have rotating parts or parts that are

 

driven by this equipment. Improper use can cause serious or fatal injury. Only qualified

 

personnel should attempt the start–up procedure or troubleshoot this equipment.

–System documentation must be available to anyone that operates this equipment at all times.

–Keep non-qualified personnel at a safe distance from this equipment.

–Only qualified personnel familiar with the safe installation, operation and maintenance of this device should attempt start-up or operating procedures.

–Always stop engine before making or removing any connections.

–Always stop engine and allow it to cool before refueling.

Responsibility When your generator is delivered, it becomes the responsibility of the owner/operator of the generator set to prevent unsafe conditions and operation of the equipment. Some responsibilities include (but are not limited to) the following:

1.It is the responsibility of the owner/operator of this generator to ensure that this equipment is correctly and safely installed.

2.It is the responsibility of the owner/operator of this generator to ensure that this equipment, when installed fully complies with all federal, state and local codes.

3.It is the responsibility of the owner/operator of this generator to ensure that any person operating this equipment has been properly trained.

4.It is the responsibility of the owner/operator of this generator to ensure that any person operating this equipment has access to all manuals and information required for the safe use and operation of this equipment.

5.It is the responsibility of the owner/operator of this generator to ensure that it is properly maintained and safety inspected at regular scheduled intervals.

6.It is the responsibility of the owner/operator of this generator to ensure that any person who has not been trained on the safe use of this equipment does not have access to this equipment.

Read This Manual Thoroughly

If you do not understand any concept, any procedure, any safety warning statement, any safety caution statement or any portion of this manual, contact Baldor or your nearest authorized Baldor representative. We are happy to make sure you understand the information in this manual so that you can safely enjoy the full use of this generator.

Baldor Generators

3815 Oregon Street

Oshkosh, WI 54902

(920) 236–4200(voice); or (920) 236–4219 (fax); or www.baldor.com

MN2412

Product Safety Information 1-1

Page 4 Page 6
Image 5
Page 4 Page 6
Contents PowerchiefR POW’R Products Generator California Proposition 65 Warning Table of Contents Ii Table of Contents MN2412 Read This Manual Thoroughly Section Product Safety InformationOperation Precaution Statements Used In This ManualProperty Operation Warning Statements Burn Installation Maintenance Product Safety Information MN2412 Section General Information Limited WarrantyWarranty Period Generator Series Labor Parts General Information MN2412 PowerchiefR Generators Storage Section Receiving & InstallationPhysical Location Frame Ground Connection Receptacle ConnectionsEngine Oil Use of Electric Motor Loads Battery ConnectionsSeries PC Recommended Engine Oil and Battery TypeOperator Control Panel Section OperationRecoil Start Start-Up Procedure Electric StartStopping Procedure Engine Section Troubleshooting and MaintenanceGeneral Service Problems and SolutionsTroubleshooting Guide Figure A-1 PC30H Operator Panel Appendix a PowerchiefR SeriesTable A-1 Generator Set Parts List Replacement PartsReceptacle, 125VAC at 15 Amps Figure A-5 PC30H Wiring Diagram Figure A-6 PC40H Wiring Diagram Figure A-7 PC50H Wiring Diagram Figure A-8 PC60H Wiring Diagram Figure A-9 PC90VE Wiring Diagram Baldor District Offices Baldor Generators

MN2412 specifications

The Baldor MN2412 is a premier electric motor known for its high efficiency, rugged construction, and advanced features that cater to various industrial and commercial applications. This motor exemplifies Baldor's commitment to quality, durability, and performance, making it an ideal choice for demanding environments.

One of the most notable characteristics of the MN2412 is its efficiency. Engineered to meet stringent NEMA Premium Efficiency standards, the motor reduces energy consumption, thereby lowering operational costs and contributing to a more sustainable environment. The efficient design minimizes heat generation, allowing the motor to operate at safe temperatures even under heavy loads.

The MN2412 features a robust construction made of high-grade materials that ensure longevity. It is equipped with high-quality bearings that provide excellent load-carrying capabilities and extended service life. The enclosure is typically made of durable cast iron, offering protection against dust and moisture while ensuring the motor can withstand harsh operating conditions.

In terms of technology, the Baldor MN2412 incorporates advanced winding designs that enhance performance and efficiency. The windings are coated for enhanced insulation, which helps to resist electrical shorts and prolong the motor's lifespan. Furthermore, the motor is designed with a removable fan cover, making maintenance and repair tasks straightforward and efficient.

Variety in design is another key feature of the MN2412. It is available in various configurations, including different voltages and horsepower ratings, allowing it to be suitable for a wide range of applications—from pumps and fans to conveyors and compressors. Additionally, the MN2412 supports dual-voltage operation, which provides flexibility in installation, allowing it to operate on different power supply systems.

Another significant advantage of the MN2412 is its low noise level. The engineering team has meticulously designed the motor to minimize vibration and operational noise, making it suitable for environments where noise reduction is essential.

The Baldor MN2412 is also integrated with capabilities for use in variable frequency drive (VFD) applications, enhancing its versatility in speed control and operational efficiency. With its adaptability and high performance, the MN2412 stands out as a reliable choice for industries requiring precision and reliability.

In summary, the Baldor MN2412 electric motor combines efficiency, durability, flexibility, and advanced technology, making it an exceptional choice for a variety of industrial applications. Its design ensures maximum uptime and minimal maintenance, contributing to overall operational success.
Top Page Image Contents