Chicago Electric 98391 manual Technical Specifications, Servicing, Maintenance Procedures

Page 16

Technical

Specifications

 

 

 

Four Stroke Single

Engine Type

 

Cylinder OHV Diesel,

 

 

 

10HP

Bore x Stroke

86x72 mm

Compression Ratio

19±:1

Displacement

418 cc

Rotation viewed from PTO

Counterclockwise

(power takeoff - the output shaft)

 

Fuel

 

Type

#2 Diesel Fuel

 

Capacity

4.2 Gallons

 

 

Engine Oil

 

Type

5W-40

 

Capacity

1-3/4 qts

 

 

Valve

 

Intake

0.10~0.15 mm

Clearance

 

Exhaust

0.10~0.15 mm

(COLD)

 

 

 

Speed

 

Idle

1,100 RPM

 

Maximum

3,600 RPM

 

 

The emission control system for this Generator’s Engine is warranted for standards set by the U.S. Environmental Protection Agency. For warranty information, refer to the last pages of this manual.

Servicing

To prevent serious injury

from accidental starting:

Turn the Power Switch of the equipment to its “OFF” position, wait for the engine to cool before performing any inspection, maintenance, or cleaning procedures.

To prevent serious injury

from equipment failure: Do not use damaged equipment. If abnormal noise, vibration, or excess smoking occurs, have the problem corrected before further use.

Maintenance Procedures

Many maintenance procedures, including those not detailed in this manual, will need to

be performed by a qualified technician for safety. If you have any doubts about your ability to safely service the equipment or engine, have a qualified technician service the equipment instead.

Note: Warranty is void if proper mainte- nance and servicing procedures are not followed.

Engine Oil Change

CAUTION! Oil is very hot during opera- tion and can cause burns. Wait for engine to cool before changing oil.

1.Place a drain pan (not included) un- derneath the crankcase’s drain plug.

2.Remove the drain plug and empty oil. Recycle used oil.

3.Inspect drain plug gasket for damage or tears. Replace gasket if damaged. Replace the drain plug and tighten it.

4.Refill the oil to the proper level follow- ing the instructions under the Starting the Engine section.

REV 09a

SKU 98391

For technical questions, please call 1-800-444-3353.

Page 16

Image 16
Contents For technical questions or replacement parts, please call Distributed exclusively by Harbor Freight ToolsContents Fuel injection pump Parts List & diagram Set up precautions Save This ManualOperating precautions Carbon Monoxide Hazard Using an engine indoorsService precautions For technical questions, please call Basic Specifications Set Up InstructionsUnpacking LocationControls 120V GfciGrounding Operating InstructionsStarting the Engine How to Shut Engine Off SKU For technical questions, please callDecompression Handle To Power Tools and Equipment Equipment OperationMounting Hole Pattern Shaft Size/Type Maintenance Procedures Technical SpecificationsServicing Air Filter Element Maintenance Storage Cleaning, Maintenance, Lubrication ScheduleDiesel Fuel and Microbes Troubleshooting Problem Possible Causes Probable Solutions Engine backfires AC output, but noPart Description Qty Main assembly PartsRecord Product’s Serial Number Here Main Assembly Diagram Cylinder Block Assembly Parts List Cylinder block assembly diagram Cylinder head Assembly Parts List Diagram Cylinder Head Bonnet Parts List & diagram Piston & connecting Rod Parts List Diagram Crank shaft Flywheel Parts List Diagram Camshaft assembly Parts List & diagram Air cleaner assembly Parts List & diagram Oil System Parts List Diagram Fuel injection pump Parts List & diagram Fuel Nozzle Parts List Diagram Governor & Control System Parts List & Diagram Fuel tank and pipe Parts List & diagram Muffler Parts List Diagram Starting motor Parts List & diagramGenerator Parts List Diagram Control panel Parts List & diagram Wiring diagram Limited 1 year / 90 Day warranty Emission Control System Warranty United States Emission Control Defects Warranty StatementAir Induction System