White Outdoor L-Syle warranty Maintaining Your Snow Thrower, Engine, Lubrication

Page 14

5

Maintaining

Your Snow

Thrower

WARNING

Before lubricating, repairing, or inspect- ing, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop.

Engine

Refer to the separate Tecumseh Engines manual packed with your unit for all engine maintenance.

Lubrication

Engine

Refer to the separate Tecumseh Engines manual packed with your unit for all engine lubrication instruc- tions.

Gear Shaft

The gear (hex) shaft should be lubricated at least once a season or after every 25 hours of operation.

1.Remove the lower frame cover by removing the two screws which secure it.

2.Apply a light coating of an all-weather multi-purpose grease to the hex shaft. See Figure 8.

Wheels

At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.

Chute Directional Control

Once a season, the joystick should be lubricated with petroleum jelly, linseed oil, mineral oil, paraffin wax or 3-in-1 oil.

Auger Shaft

At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 9.

Gear Case

The auger gear case has been filled with grease at the factory. If disassembled for any reason, lubricate with two ounces of grease (Part Number 737-0168).

NOTE: Do not overfill the gear case. Damage to the seals could result. Be sure the vent plug is free of grease in order to relieve pressure.

Figure 8

��������� ������� �������

Figure 9

Avoid oil spillage on rubber friction wheel and aluminum drive plate.

Do not overfill the gear case. Damage to the seals could result.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes:

1.Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower.

2.Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figure 10.

To remove shave plate:

1.Remove the carriage bolts and hex nuts which attach it to the snow thrower housing.

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

���������������������������������

Figure 10

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OPERATOR’S Manual MTD LLC, P.O. BOX 361131 CLEVELAND, OhioTable of Contents Chute clean-out tool is fastened to the top Your ResponsibilityTrainingPreparation Your Responsibility Restrict the useDo not modify engine Maintenance & StorageOperation Your ResponsibilitySetting Up Your Snow ThrowerShear Pin Storage Setting Up Your Snow ThrowerChute Clean-Out Tool Tire PressureOperating Your Snow ThrowerOperating Your Snow Thrower Stopping The Engine Gas & Oil Fill-UpStarting The Engine To Engage Augers Chute Clean-Out ToolTo Engage Drive Recoil StarterShift Cable Chute Directional ControlMaking Lubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid ShoesAuger Belt Replacement Place a piece of plastic under the gas capDrive Belt Replacement Friction Wheel Removal Cracking and replace if necessaryPreparing Snow Thrower Off-Season StoragePreparing Engine Trouble Shooting Problem Cause RemedyStyle L Illustrated Parts List To order replacement Parts, contact Or visitStyle L 738-04194 Flange Shoulder Screw Style L Disc, Friction Wheel Page Page MANUFACTURER’S Limited Warranty for MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone
Top Page Image Contents