White Outdoor L-Syle warranty Off-Season Storage, Preparing Engine, Preparing Snow Thrower

Page 18

7

Off-Season

Storage

WARNING

Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

Drain fuel into an approved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

Do not drain carburetor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last pos- sibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top performance from the snow thrower for many more years.

Preparing Engine

WARNING: Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

NOTE: It is important to prevent gum deposits from form- ing in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose or tank during storage.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Follow these instructions to prepare your snow thrower for storage:

WARNING: Drain fuel into an ap- proved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke.

Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

1.Remove all gasoline from the carburetor and the fuel tank to prevent gum deposits from forming on these parts and harming the engine.

2.Run the engine until the fuel tank is empty and it stops due to lack of fuel.

3.Drain carburetor by pressing upward on bowl drain, located below the carburetor cover (refer to the Tecumseh engine manual for more detailed instruc- tion).

WARNING: Do not drain carbure- tor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

NOTE: Fuel stabilizer (such as STA-BIL) is an accept- able alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow it to reach the carburetor. Do not drain carburetor if using fuel stabilizer.

4.Remove the spark plug and pour one (1) ounce of engine oil through the spark plug hole into the cylinder. Cover spark plug hole with a rag and crank the engine several times to distribute the oil. Replace spark plug.

NOTE: Refer to the Tecumseh engine manual for more information on preparing the snow thrower engine for storage.

Preparing Snow Thrower

1.When storing the snow thrower in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

2.Remove all dirt from exterior of engine and equipment.

3.Follow lubrication recommendations on page 12.

4.Store equipment in a clean, dry area.

18

Image 18
Contents OPERATOR’S Manual MTD LLC, P.O. BOX 361131 CLEVELAND, OhioTable of Contents Chute clean-out tool is fastened to the top Your ResponsibilityTrainingPreparation Your Responsibility Restrict the useDo not modify engine Maintenance & StorageOperation Your ResponsibilitySetting Up Your Snow ThrowerShear Pin Storage Setting Up Your Snow ThrowerChute Clean-Out Tool Tire PressureOperating Your Snow ThrowerOperating Your Snow Thrower Gas & Oil Fill-Up Starting The EngineStopping The Engine To Engage Augers Chute Clean-Out ToolTo Engage Drive Recoil StarterShift Cable Chute Directional ControlMaking Lubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid ShoesAuger Belt Replacement Place a piece of plastic under the gas capDrive Belt Replacement Friction Wheel Removal Cracking and replace if necessaryOff-Season Storage Preparing EnginePreparing Snow Thrower Trouble Shooting Problem Cause RemedyStyle L Illustrated Parts List To order replacement Parts, contact Or visitStyle L 738-04194 Flange Shoulder Screw Style L Disc, Friction Wheel Page Page MANUFACTURER’S Limited Warranty for MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone