Sears 944.528117 HOW to USE Your Snow Thrower, Stopping, Traction Drive, Auger, Engine

Page 11

PE

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result insevere eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any adjust-

ments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

Release the auger control lever to stop throwing snow.

ENGINE

1. Move ON / OFF switch to "OFF" position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE CHOKE CONTROL (See Fig. 11)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

FIG. 11

TO CONTROL SNOW DISCHARGE (See Fig. 12)

WARNING: Snow throwers have ex=

posed rotating parts, which can cause

&severe injury from contact, or from ma= terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: if the discharge chute or

and wait for all moving parts to stop. Use auger become clogged, shut=off engine the clean=out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled

by the discharge chute control lever.

To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to

throw snow a short distance; set the deflector higher to throw snow farther.

Press downward on chute deflector control lever and move lever forward to lower the deflector and decrease the distance. Move lever back to raise the deflector and increase the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROLLEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 12

TO THROW SNOW (See Fig. 13)

The auger rotation is controlled by the auger control lever located on the right side handle.

Squeeze auger control lever to handle to engage the auger and throw snow.

Release the auger control lever to stop throwing snow.

AUGER

FIG. 13

11

Image 11 Contents
Powe -P LLE Safe Operation Practices for Walk-Behind Snow Throwers Contents Page Operatio HOW to SET UP Your Snow ThrowerParts Packe ELY CartonSee Figs Install Traction Drive Control RODAsse BLY/PRE-OPERATION Unfold Upper HandleOperatic Install Discharge Chute / Chute RotaterASS Check Tire Pressure Install Chute Deflector Remote ControlKnow Your Snow Thrower Operati Meets A.N.S.I. Safety RequirementsAuger HOW to USE Your Snow ThrowerStopping Traction DriveOperation Cold Start Electric Starter Before Starting the EngineTo Start Engine Before Stopping Warm Start Electric StarterCold Start Recoil Starter Warm Start Recoil StarterTires General RecommendationsBefore Each USE Snow ThrowerEngine CleaningEquipment shear bolts as supplied with your snow thrower To Adjust Snow Thrower HeightSeadj Ents Seadj Engine Speed CarburetorEngine OIL StorageOther Fuel SystemOTI Problem Cause CorrectionExploded \17DESCRiPTiON Carriage Auger HousingDescription Scraper BARPart KEYDeflector Weldment Deflector Control AssemblyService Part Deflector Control Chute WeldmentRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadInterlock Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Wire HarnessSpacer Sprocket Axle AssemblyAssy of IA,1B Axle Shaft2325 01.02.013-A END Plate Speed Selector AssemblyDrive Plate Assembly Rubber RingEngine Mount Plate Cover AssemblyFrame Washer Idler ARM Bracket KEY Part NO. noImpeller Belt Traction BeltKEY Part Wheel AssemblyWrench Power CordSafety Ignition KEY Retainer PINInstruction Service Notes Engine 472 Model DIPSTICK/TUBE Assembly Wire AssemblySWITCH-STOP Control Bracket BOOT-SPARK PlugWWW,SeSrS,C8 800-.4-.MY-.HOME