Sears 944.528117 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

iMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

&Look for this symbol to point out ira= portant safety precautions. It means CAUTION!!! BECOMEALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark

&plug wire and place it where it cannot contact plug in order to prevent acci= dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for

use on sidewalks, driveways and other ground level surfaces. Caution should

be exercised while using on sloping sur= faces. Do not use snow thrower on

surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

&

_

&

WARNING: Snow throwers have ex=

posed rotating parts, which can cause severe injury from contact, or from ma= terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION:parts becomeMufflerextremelyand otherhot engineduring operation and remain hot after engine

contact,has stoppedstay. Toawayavoidfromseveretheseburnsareason.

WARNING: Engine exhaust, some of its constituents, and certain vehicle

components contain or emit chemi= cals known to the State of California

to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never

allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot engine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refueling is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors

or electric starting motors.

. Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

. Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to

protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller housing or discharge chute, and when making any repairs, adjustments or inspections.

2

Image 2
Contents Powe -P LLE Safe Operation Practices for Walk-Behind Snow Throwers Contents Page ELY Carton HOW to SET UP Your Snow ThrowerParts Packe OperatioUnfold Upper Handle Install Traction Drive Control RODAsse BLY/PRE-OPERATION See FigsOperatic Install Discharge Chute / Chute RotaterASS Install Chute Deflector Remote Control Check Tire PressureKnow Your Snow Thrower Meets A.N.S.I. Safety Requirements OperatiTraction Drive HOW to USE Your Snow ThrowerStopping AugerOperation Cold Start Electric Starter Before Starting the EngineTo Start Engine Warm Start Recoil Starter Warm Start Electric StarterCold Start Recoil Starter Before StoppingSnow Thrower General RecommendationsBefore Each USE TiresCleaning EngineEquipment shear bolts as supplied with your snow thrower To Adjust Snow Thrower HeightSeadj Ents Seadj Carburetor Engine SpeedFuel System StorageOther Engine OILProblem Cause Correction OTI\17 ExplodedDESCRiPTiON Scraper BAR Auger HousingDescription CarriageKEY PartChute Weldment Deflector Control AssemblyService Part Deflector Control Deflector WeldmentRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketInterlock Wire Harness Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPSpacer Axle Shaft Axle AssemblyAssy of IA,1B Sprocket2325 01.02.013-A Rubber Ring Speed Selector AssemblyDrive Plate Assembly END PlateEngine Mount Plate Cover AssemblyFrame Traction Belt KEY Part NO. noImpeller Belt Washer Idler ARM BracketWheel Assembly KEY PartRetainer PIN Power CordSafety Ignition KEY WrenchInstruction Service Notes Engine 472 Model BOOT-SPARK Plug Wire AssemblySWITCH-STOP Control Bracket DIPSTICK/TUBE Assembly800-.4-.MY-.HOME WWW,SeSrS,C8

944.528117 specifications

The Sears Model 944.528117 stands as a testament to the ingenuity of home appliances during its time. Known for its combination of functionality and reliability, this model gained popularity among households seeking efficiency and performance in their everyday chores. The Sears 944.528117 is a washing machine designed to cater to a wide range of laundry needs, all while ensuring ease of use and energy efficiency.

One of the standout features of the Sears 944.528117 is its user-friendly control panel. The intuitive design allows users to effortlessly select various wash cycles and settings, ensuring that any type of fabric or load size is adequately addressed. The machine comes equipped with multiple wash cycles, including options for delicate fabrics, heavy-duty loads, and quick washes. This versatility ensures that users can tailor their laundry experience to the specific needs of their garments.

Another significant characteristic of the Sears 944.528117 is its water efficiency. The washing machine integrates advanced technologies that optimize water usage, thereby minimizing environmental impact while still delivering excellent cleaning results. This feature is particularly appealing to eco-conscious consumers who are looking for sustainable options in their home appliances.

In terms of performance, the Sears 944.528117 employs a high-speed spin cycle that effectively removes excess water from clothes, significantly reducing drying time. This not only enhances user convenience but also contributes to energy savings by reducing the need for prolonged dryer use.

Furthermore, the machine's durable construction ensures longevity, making it a reliable investment for any household. Its robust design also minimizes vibrations during operation, resulting in quieter washes and a more pleasant laundry experience overall.

For convenience, the Sears 944.528117 features a large capacity drum, allowing users to wash larger loads at once. This is particularly beneficial for families or individuals with busy lifestyles, as it reduces the number of laundry cycles needed and saves valuable time.

In summary, the Sears 944.528117 offers a blend of functionality, efficiency, and durability. With its user-friendly interface, versatile wash cycles, water-saving technologies, high-speed performance, and spacious design, it represents a practical solution for modern laundry needs. This model remains a reliable choice for those seeking dependable performance in their washing machine.