Sears 944.528117 owner manual Engine, Cleaning

Page 16

NTE

AUGER GEAR CASE

The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo= nents can cause contamination of the friction

wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG-SL. Select the oil'sSAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

I

 

I

 

i °F

-20

0

30

32

40

°c -30

-2'o

-1'0

6

lo

TEMPERATURE RANGE ANTICIPATED

BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°R Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changethe oilafter every25 hours of operation orat leastonce ayear if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG-SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

A CE

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See "TO REMOVE WHEELS" in the Service and Adjustments section of this manual).

1.Remove safety ignitionkey and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Besureto install klik pin into proper hole in wheel axle (See "TO REMOVE WHEELS" in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour

slowly. Do not overfill. For approximate capacity see "PRODUCT SPECI FICATIONS" section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at "FULE'line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark

plug type and gap setting are shown in the "PRODUCT SPECIFICATIONS" section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower

housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

&and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.WARNING: Remove safety ignition key

eKeep finished surfaces/wheels free of gasoline, oil, etc.

eWe do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Powe -P LLE Safe Operation Practices for Walk-Behind Snow Throwers Contents Page HOW to SET UP Your Snow Thrower Parts PackeELY Carton OperatioInstall Traction Drive Control ROD Asse BLY/PRE-OPERATIONUnfold Upper Handle See FigsASS Install Discharge Chute / Chute RotaterOperatic Install Chute Deflector Remote Control Check Tire PressureKnow Your Snow Thrower Meets A.N.S.I. Safety Requirements OperatiHOW to USE Your Snow Thrower StoppingTraction Drive AugerOperation To Start Engine Before Starting the EngineCold Start Electric Starter Warm Start Electric Starter Cold Start Recoil StarterWarm Start Recoil Starter Before StoppingGeneral Recommendations Before Each USESnow Thrower TiresCleaning EngineSeadj Ents To Adjust Snow Thrower HeightEquipment shear bolts as supplied with your snow thrower Seadj Carburetor Engine SpeedStorage OtherFuel System Engine OILProblem Cause Correction OTI\17 ExplodedDESCRiPTiON Auger Housing DescriptionScraper BAR CarriageKEY PartDeflector Control Assembly Service Part Deflector ControlChute Weldment Deflector WeldmentLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketInterlock Impeller ROD Assembly Traction ROD AssemblyWire Harness Shifter ROD TOPSpacer Axle Assembly Assy of IA,1BAxle Shaft Sprocket2325 01.02.013-A Speed Selector Assembly Drive Plate AssemblyRubber Ring END PlateFrame Cover AssemblyEngine Mount Plate KEY Part NO. no Impeller BeltTraction Belt Washer Idler ARM BracketWheel Assembly KEY PartPower Cord Safety Ignition KEYRetainer PIN WrenchInstruction Service Notes Engine 472 Model Wire Assembly SWITCH-STOP Control BracketBOOT-SPARK Plug DIPSTICK/TUBE Assembly800-.4-.MY-.HOME WWW,SeSrS,C8

944.528117 specifications

The Sears Model 944.528117 stands as a testament to the ingenuity of home appliances during its time. Known for its combination of functionality and reliability, this model gained popularity among households seeking efficiency and performance in their everyday chores. The Sears 944.528117 is a washing machine designed to cater to a wide range of laundry needs, all while ensuring ease of use and energy efficiency.

One of the standout features of the Sears 944.528117 is its user-friendly control panel. The intuitive design allows users to effortlessly select various wash cycles and settings, ensuring that any type of fabric or load size is adequately addressed. The machine comes equipped with multiple wash cycles, including options for delicate fabrics, heavy-duty loads, and quick washes. This versatility ensures that users can tailor their laundry experience to the specific needs of their garments.

Another significant characteristic of the Sears 944.528117 is its water efficiency. The washing machine integrates advanced technologies that optimize water usage, thereby minimizing environmental impact while still delivering excellent cleaning results. This feature is particularly appealing to eco-conscious consumers who are looking for sustainable options in their home appliances.

In terms of performance, the Sears 944.528117 employs a high-speed spin cycle that effectively removes excess water from clothes, significantly reducing drying time. This not only enhances user convenience but also contributes to energy savings by reducing the need for prolonged dryer use.

Furthermore, the machine's durable construction ensures longevity, making it a reliable investment for any household. Its robust design also minimizes vibrations during operation, resulting in quieter washes and a more pleasant laundry experience overall.

For convenience, the Sears 944.528117 features a large capacity drum, allowing users to wash larger loads at once. This is particularly beneficial for families or individuals with busy lifestyles, as it reduces the number of laundry cycles needed and saves valuable time.

In summary, the Sears 944.528117 offers a blend of functionality, efficiency, and durability. With its user-friendly interface, versatile wash cycles, water-saving technologies, high-speed performance, and spacious design, it represents a practical solution for modern laundry needs. This model remains a reliable choice for those seeking dependable performance in their washing machine.
Top Page Image Contents