Poulan 424704, PR5524ESLCT owner manual Engine, Cleaning

Page 14

MAINTENANCE

V-BELTS

Check V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life..

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Exploded KEY Part Description Auger Assembly RH Auger HousingAuger Assembly LH Scrapper BARPALIER, Tarière BouchonDeflector Seal Chute WeldmentDeflector Weldment StrapRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley PivotLower Handle Panel Bracket LH Panel Bracket RHHandle Grip Pivot Support WeldmentKnob RED SpacerRetainer Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Headlight Bezel Wire HarnessConsole Panel Flood HeadlightItem 43 Exploded END Plate Speed Selector Assembly43 402689 Drive Plate Assembly Control ARMSprocket Axle ShaftRoll PIN 3/16 Clik PINKEY Part Description Engine LCT Model PLMHK18600781DE 423184X428 Engine Mount PlateImpeller Belt Belt CoverTraction Belt Repair Parts Snow Thrower - Model Number PR5524ESLCT Wheels Wheel Assembly LHRetainer PIN Power CordSafety Ignition KEY WrenchDECAL, DANGER, Deflector DECAL, DangerDecal DECAL, InstructionService Notes Service Notes Limited Warranty

PR5524ESLCT, 424704 specifications

The Poulan PR5524ESLCT is a robust and efficient gas-powered lawn mower designed to make yard work a breeze. Featuring a powerful 140cc engine, this machine provides effective cutting performance for a variety of grass types and conditions. Its ability to tackle tough lawns with ease makes it a favorite among homeowners and landscaping professionals alike.

One of the standout features of the PR5524ESLCT is its 22-inch cutting deck. This ample cutting size allows for wider paths, reducing the time spent mowing and ensuring a cleaner cut. The deck is constructed from durable materials that can withstand harsh conditions, providing long-lasting reliability. Additionally, its cutting height adjustment is easily operated with a single lever, allowing users to customize their mowing experience with six different height settings.

Equipped with the Easy Start technology, the Poulan PR5524ESLCT is designed for effortless ignition. This feature significantly reduces the hassle of traditional starting methods, enabling users to get right to work without wasted time. The mower's engine is engineered for optimal fuel efficiency, which translates to longer run times between refueling.

Another remarkable feature of this model is its rear bagging and mulching capabilities. The mower comes with a rear bag that collects grass clippings for easy disposal, helping to maintain your lawn's pristine appearance. For those who prefer to return nutrients to the soil, the mulching function finely chops grass clippings, promoting a healthier lawn.

The PR5524ESLCT also boasts a rugged design that emphasizes user comfort. Its lightweight construction allows for easy maneuverability, while the ergonomically designed handles reduce user fatigue during longer mowing sessions. The folding handle feature facilitates compact storage, saving space in your garage or shed.

Safety is a top priority, and this mower is equipped with a safety guard that helps prevent accidental starting. It also includes a reliable braking system for added peace of mind. With its combination of power, efficiency, and user-friendly features, the Poulan PR5524ESLCT is an excellent choice for anyone looking to maintain a beautiful lawn effortlessly. Whether you’re a seasoned lawn care professional or a homeowner, this mower delivers top-notch performance with every use.
Top Page Image Contents