Poulan PR5524ESLCT Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 15

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or ad- justments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 18)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug. Replace safety ignition key

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 15

4. Connect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

SPACER

 

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 18

TO REMOVE BELT COVER (See Fig. 19)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 19

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Exploded KEY Part Description Scrapper BAR Auger HousingAuger Assembly LH Auger Assembly RHBouchon PALIER, TarièreStrap Chute WeldmentDeflector Weldment Deflector SealPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketPivot Support Weldment Panel Bracket LH Panel Bracket RHHandle Grip Lower HandleHandle Knob SpacerRetainer Knob REDCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Flood Headlight Wire HarnessConsole Panel Headlight BezelItem 43 Exploded Control ARM Speed Selector Assembly43 402689 Drive Plate Assembly END PlateClik PIN Axle ShaftRoll PIN 3/16 Sprocket423184X428 Engine Mount Plate KEY Part Description Engine LCT Model PLMHK18600781DEBelt Cover Traction BeltImpeller Belt Wheel Assembly LH Repair Parts Snow Thrower - Model Number PR5524ESLCT WheelsWrench Power CordSafety Ignition KEY Retainer PINDECAL, Instruction DECAL, DangerDecal DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

PR5524ESLCT, 424704 specifications

The Poulan PR5524ESLCT is a robust and efficient gas-powered lawn mower designed to make yard work a breeze. Featuring a powerful 140cc engine, this machine provides effective cutting performance for a variety of grass types and conditions. Its ability to tackle tough lawns with ease makes it a favorite among homeowners and landscaping professionals alike.

One of the standout features of the PR5524ESLCT is its 22-inch cutting deck. This ample cutting size allows for wider paths, reducing the time spent mowing and ensuring a cleaner cut. The deck is constructed from durable materials that can withstand harsh conditions, providing long-lasting reliability. Additionally, its cutting height adjustment is easily operated with a single lever, allowing users to customize their mowing experience with six different height settings.

Equipped with the Easy Start technology, the Poulan PR5524ESLCT is designed for effortless ignition. This feature significantly reduces the hassle of traditional starting methods, enabling users to get right to work without wasted time. The mower's engine is engineered for optimal fuel efficiency, which translates to longer run times between refueling.

Another remarkable feature of this model is its rear bagging and mulching capabilities. The mower comes with a rear bag that collects grass clippings for easy disposal, helping to maintain your lawn's pristine appearance. For those who prefer to return nutrients to the soil, the mulching function finely chops grass clippings, promoting a healthier lawn.

The PR5524ESLCT also boasts a rugged design that emphasizes user comfort. Its lightweight construction allows for easy maneuverability, while the ergonomically designed handles reduce user fatigue during longer mowing sessions. The folding handle feature facilitates compact storage, saving space in your garage or shed.

Safety is a top priority, and this mower is equipped with a safety guard that helps prevent accidental starting. It also includes a reliable braking system for added peace of mind. With its combination of power, efficiency, and user-friendly features, the Poulan PR5524ESLCT is an excellent choice for anyone looking to maintain a beautiful lawn effortlessly. Whether you’re a seasoned lawn care professional or a homeowner, this mower delivers top-notch performance with every use.
Top Page Image Contents