Poulan 96192004300, 436134 owner manual Auger 27 LH, Auger 27 RH, Skid Plate LH, Skid Plate RH

Page 23

REPAIR PARTS SNOW THROWER - - MODEL NO. PR827ES (96192004300)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART
NO.	NO.	DESCRIPTION
1	420495X431	AUGER 27 LH
2	420496X431	AUGER 27 RH

01.07.018-A

		3		2
		3
		KEY	PART
		NO.	NO.	DESCRIPTION
		1	174762X431	SKID PLATE LH
		2	178777X431	SKID PLATE RH
		3	72270506	CARRIAGE BOLT 5/16−18 X .75
4	1	4	751153	NUT 5/16−18
	1
	01.11.001-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 23

Image 23

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsTraction OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Auger Bearing Auger HousingKEY Part Description Scraper BARSkid Plate RH Auger 27 LHAuger 27 RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool BearingDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldLoop Handle LH Repair Parts Snow Thrower - Model NO. PR827ES HandlesLower Handle Pivot Support WeldmentFlood Headlight Wire HarnessConsole Panel Headlight BezelWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. PR827ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 SprocketEngine Mount Plate Engine Model 12A114Frame 436146X421Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket432336X428 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 432335X428193071 Repair Parts Snow Thrower - Model NO. PR827ES BAG of PartsSafety Ignition KEY KIT Harness Conn B&S Shifter ROD TOP Shifter ROD Bottom435840 DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DangerService Notes Service Notes Service Notes Limited Warranty

KEY

AUGER 27 LH

AUGER 27 RH

KEY

SKID PLATE LH

SKID PLATE RH