Poulan 436134 Chute Weldment, Deflector Weldment, Deflector Control Assembly, Deflector Seal

Page 26

REPAIR PARTS SNOW THROWER - - MODEL NO. PR827ES (96192004300)

CONTROL PANEL / DISCHARGE CHUTE

5

7

15

3

16

			*14		*11
					*11
			2		*10
				6	*10
			4	6
			4
KEY	PART		6		*13
KEY	PART				*13
NO.	NO.	DESCRIPTION
1	435023X421	CHUTE WELDMENT	1		*12
2	178633X421	DEFLECTOR WELDMENT
3	420673	DEFLECTOR CONTROL ASSEMBLY
4	420325	DEFLECTOR SEAL
5	414280	KNOB BLACK
6	128415	POP RIVET	6
7	17501010	SCREW 10-24 X .625	8	9
8	430324	CHUTE SNOW SHIELD	8		01.09.015-B
9	419822X431	SHIELD RETAINER STRAP
*10	179829	SHOULDER BOLT 1/4-20 X .375
*11	191730	NUT 1/4-20
*12	72250505	CARRIAGE BOLT 3/8-16 X .625
*13	751153	NUT 5/16-18
*14	184505	DEFLECTOR SPRING

15420679 (SERVICE PART) DEFLECTOR CONTROL

16420672 (SERVICE PART) DEFLECTOR CABLE BLACK

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

26

Image 26

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Scraper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger 27 LHAuger 27 RH Skid Plate RHExploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller PulleyDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadPivot Support Weldment Repair Parts Snow Thrower - Model NO. PR827ES HandlesLower Handle Loop Handle LHHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR827ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PIN436146X421 Engine Model 12A114Frame Engine Mount PlateIdler ARM Bracket Impeller BeltTraction Belt Idler Pulley432335X428 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 432336X428193071 Repair Parts Snow Thrower - Model NO. PR827ES BAG of PartsSafety Ignition KEY KIT Harness Conn B&S Shifter ROD TOP Shifter ROD Bottom435840 DECAL, Danger Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Service Notes Limited Warranty