Poulan 436134, 96192004300 owner manual Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

AUGER CONTROL ROD

AUGER

RETAINER

CONTROL

LEVER

SPRING

 

 

AUGER

CONTROL

BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces- sary, rotatechute assembly to align square and pin on un- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE

 

 

ROTATOR

 

3/8 LOCKNUT

HEAD

 

 

 

 

3/8 WASHER

 

 

PIN

 

 

THREADED

 

 

STUD

 

ALIGN BEFORE

ROTATOR HEAD

CHUTE

MOUNTING

BRACKET

TIGHTENING LOCKNUT

BRACKET

FIG. 7

6

Image 6
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Scraper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger 27 LHAuger 27 RH Skid Plate RHExploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller PulleyDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadPivot Support Weldment Repair Parts Snow Thrower - Model NO. PR827ES HandlesLower Handle Loop Handle LHHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR827ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PIN436146X421 Engine Model 12A114Frame Engine Mount PlateIdler ARM Bracket Impeller BeltTraction Belt Idler Pulley432335X428 Repair Parts Snow Thrower - Model NO. PR827ES WheelsWheel Assembly LH 432336X428Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts Safety Ignition KEY193071 Shifter ROD TOP Shifter ROD Bottom 435840KIT Harness Conn B&S DECAL, Danger Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Service Notes Limited Warranty