Poulan 199329, 96192000600 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Tool BOX See Fig Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Engine CleaningService and Adjustments To Adjust Snow Thrower HeightChute Deflector Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting Limited Warranty

199329, 96192000600 specifications

The Poulan model 199329,96192000600 is a powerful and versatile tool designed for various outdoor maintenance tasks. This particular model is often recognized for its efficiency and user-friendly features, making it a go-to choice for homeowners, landscapers, and gardening enthusiasts.

One of the standout features of the Poulan 199329,96192000600 is its robust engine. Equipped with a reliable, high-performance motor, this tool ensures ample power to tackle demanding jobs such as trimming, cutting, and pruning. The engine is designed to operate smoothly, providing consistent power output while maintaining fuel efficiency, which is a critical consideration for users looking to minimize operational costs over time.

Another distinguishing characteristic of this model is its lightweight design. Weighing in at an easily manageable figure, the Poulan 199329,96192000600 allows for prolonged use without excessive fatigue. This aspect is particularly beneficial for users engaging in extensive lawn care or landscaping activities, as it helps enhance maneuverability and ease of use.

In terms of ergonomic features, the handle design is crafted to provide maximum comfort. The soft-grip handle minimizes vibrations, ensuring that users have a comfortable grip while working, further reducing fatigue during long sessions. This user-centric approach extends to the overall design of the tool, which allows for easy accessibility to controls and features, making it suitable for both novice and experienced users alike.

Technology plays a vital role in the performance of the Poulan 199329,96192000600. It incorporates advanced safety features, such as an emergency stop mechanism and safety shields, to protect users during operation. These features instill confidence, particularly for those who may be less familiar with power tools.

Additionally, this model often comes equipped with easy-start technology, which facilitates effortless ignition. This is a significant advantage for users who may struggle with traditional starting mechanisms. The ease of starting ensures that users can get to work without unnecessary delays.

Maintenance is also simplified with the Poulan 199329,96192000600. The tool is designed for easy access to the parts requiring regular upkeep, ensuring that users can keep their equipment in top shape with minimal hassle.

Overall, the Poulan 199329,96192000600 stands out as a reliable, efficient, and user-friendly equipment, making it an excellent choice for anyone in need of a quality outdoor tool to handle various yard tasks.
Top Page Image Contents