Poulan 96192000600, 199329 owner manual Storage, Other

Page 18

SERVICE AND ADJUSTMENTS

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Tool BOX See FigInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting Limited Warranty

199329, 96192000600 specifications

The Poulan model 199329,96192000600 is a powerful and versatile tool designed for various outdoor maintenance tasks. This particular model is often recognized for its efficiency and user-friendly features, making it a go-to choice for homeowners, landscapers, and gardening enthusiasts.

One of the standout features of the Poulan 199329,96192000600 is its robust engine. Equipped with a reliable, high-performance motor, this tool ensures ample power to tackle demanding jobs such as trimming, cutting, and pruning. The engine is designed to operate smoothly, providing consistent power output while maintaining fuel efficiency, which is a critical consideration for users looking to minimize operational costs over time.

Another distinguishing characteristic of this model is its lightweight design. Weighing in at an easily manageable figure, the Poulan 199329,96192000600 allows for prolonged use without excessive fatigue. This aspect is particularly beneficial for users engaging in extensive lawn care or landscaping activities, as it helps enhance maneuverability and ease of use.

In terms of ergonomic features, the handle design is crafted to provide maximum comfort. The soft-grip handle minimizes vibrations, ensuring that users have a comfortable grip while working, further reducing fatigue during long sessions. This user-centric approach extends to the overall design of the tool, which allows for easy accessibility to controls and features, making it suitable for both novice and experienced users alike.

Technology plays a vital role in the performance of the Poulan 199329,96192000600. It incorporates advanced safety features, such as an emergency stop mechanism and safety shields, to protect users during operation. These features instill confidence, particularly for those who may be less familiar with power tools.

Additionally, this model often comes equipped with easy-start technology, which facilitates effortless ignition. This is a significant advantage for users who may struggle with traditional starting mechanisms. The ease of starting ensures that users can get to work without unnecessary delays.

Maintenance is also simplified with the Poulan 199329,96192000600. The tool is designed for easy access to the parts requiring regular upkeep, ensuring that users can keep their equipment in top shape with minimal hassle.

Overall, the Poulan 199329,96192000600 stands out as a reliable, efficient, and user-friendly equipment, making it an excellent choice for anyone in need of a quality outdoor tool to handle various yard tasks.
Top Page Image Contents