Poulan 199329 To Remove Wheels See Fig, Remove the klik pin and remove wheel from axle

Page 17

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing

the snow thrower together.

17

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

HOUSING

 

 

FIG. 23

TO REMOVE WHEELS (See Fig. 24)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 24

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Tool BOX See FigInstall Auger Control ROD See Figs Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting Limited Warranty

199329, 96192000600 specifications

The Poulan model 199329,96192000600 is a powerful and versatile tool designed for various outdoor maintenance tasks. This particular model is often recognized for its efficiency and user-friendly features, making it a go-to choice for homeowners, landscapers, and gardening enthusiasts.

One of the standout features of the Poulan 199329,96192000600 is its robust engine. Equipped with a reliable, high-performance motor, this tool ensures ample power to tackle demanding jobs such as trimming, cutting, and pruning. The engine is designed to operate smoothly, providing consistent power output while maintaining fuel efficiency, which is a critical consideration for users looking to minimize operational costs over time.

Another distinguishing characteristic of this model is its lightweight design. Weighing in at an easily manageable figure, the Poulan 199329,96192000600 allows for prolonged use without excessive fatigue. This aspect is particularly beneficial for users engaging in extensive lawn care or landscaping activities, as it helps enhance maneuverability and ease of use.

In terms of ergonomic features, the handle design is crafted to provide maximum comfort. The soft-grip handle minimizes vibrations, ensuring that users have a comfortable grip while working, further reducing fatigue during long sessions. This user-centric approach extends to the overall design of the tool, which allows for easy accessibility to controls and features, making it suitable for both novice and experienced users alike.

Technology plays a vital role in the performance of the Poulan 199329,96192000600. It incorporates advanced safety features, such as an emergency stop mechanism and safety shields, to protect users during operation. These features instill confidence, particularly for those who may be less familiar with power tools.

Additionally, this model often comes equipped with easy-start technology, which facilitates effortless ignition. This is a significant advantage for users who may struggle with traditional starting mechanisms. The ease of starting ensures that users can get to work without unnecessary delays.

Maintenance is also simplified with the Poulan 199329,96192000600. The tool is designed for easy access to the parts requiring regular upkeep, ensuring that users can keep their equipment in top shape with minimal hassle.

Overall, the Poulan 199329,96192000600 stands out as a reliable, efficient, and user-friendly equipment, making it an excellent choice for anyone in need of a quality outdoor tool to handle various yard tasks.
Top Page Image Contents