Poulan 96192001200 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure throttle is in STOP position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot contact plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4. Connect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

SPACER

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

AUGER HUB

AUGER SHAFT

LOCKNUT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

FRAME

BELT COVER

SCREWS

FIG. 22

TO REPLACE BELTS (See Fig. 23)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to

16 the snow thrower.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Check Tire PressureOperation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting 5518 KEY Part Description 205 183334 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive Repair Parts Snow Thrower Model PP10530ES Drive Page KEY Part Description Repair Parts Repair Parts Limited Warranty

407885, 96192001200 specifications

The Poulan 96192001200,407885 is a high-performance gas-powered chainsaw designed to meet the needs of both casual users and professionals. This versatile tool is engineered with advanced technologies and features that enhance its efficiency, usability, and durability, making it a preferred choice for various cutting tasks.

One of the standout characteristics of the Poulan 96192001200,407885 is its powerful engine. The chainsaw is equipped with a robust 40cc 2-cycle engine, which provides ample power for heavy-duty cutting and trimming tasks. This engine delivers a reliable and consistent cutting performance, allowing users to tackle thicker branches and larger logs with ease.

The chainsaw incorporates an easy-start system, which significantly reduces the effort required to start the engine. This technology is particularly beneficial for users who may struggle with traditional starting mechanisms, allowing for a hassle-free experience right from the beginning.

Another notable feature of the Poulan chainsaw is its lightweight design. Weighing in at just around 10 pounds, this chainsaw is easy to maneuver, making it suitable for extended use without causing excessive fatigue. This ergonomic design is complemented by a comfortable handle that promotes a secure grip, further enhancing user control and comfort during operation.

In terms of safety, the Poulan 96192001200,407885 is equipped with a chain brake that engages automatically in the event of kickback. This critical safety feature helps prevent accidents, ensuring that users can work confidently while minimizing risk. Additionally, the chainsaw has an adjustable chain oiling system, which allows users to manage oil flow based on their cutting needs, ensuring the chain operates smoothly and reduces wear.

The chainsaw also features a 16-inch cutting bar, providing a balance between cutting capacity and maneuverability. This size is ideal for a variety of tasks, including cutting firewood, felling small trees, and pruning large branches.

Overall, the Poulan 96192001200,407885 is a reliable and efficient chainsaw that combines power, safety, and user-friendly features, making it an essential tool for homeowners and professionals alike. Whether for yard maintenance or more demanding forestry tasks, this chainsaw promises to deliver exceptional performance every time it is put to use.
Top Page Image Contents