Poulan 96192001200, 407885 owner manual Storage, Other

Page 18

SERVICE AND ADJUSTMENTS

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Check Tire PressureOperation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting 5518 KEY Part Description 205 183334 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive Repair Parts Snow Thrower Model PP10530ES Drive Page KEY Part Description Repair Parts Repair Parts Limited Warranty

407885, 96192001200 specifications

The Poulan 96192001200,407885 is a high-performance gas-powered chainsaw designed to meet the needs of both casual users and professionals. This versatile tool is engineered with advanced technologies and features that enhance its efficiency, usability, and durability, making it a preferred choice for various cutting tasks.

One of the standout characteristics of the Poulan 96192001200,407885 is its powerful engine. The chainsaw is equipped with a robust 40cc 2-cycle engine, which provides ample power for heavy-duty cutting and trimming tasks. This engine delivers a reliable and consistent cutting performance, allowing users to tackle thicker branches and larger logs with ease.

The chainsaw incorporates an easy-start system, which significantly reduces the effort required to start the engine. This technology is particularly beneficial for users who may struggle with traditional starting mechanisms, allowing for a hassle-free experience right from the beginning.

Another notable feature of the Poulan chainsaw is its lightweight design. Weighing in at just around 10 pounds, this chainsaw is easy to maneuver, making it suitable for extended use without causing excessive fatigue. This ergonomic design is complemented by a comfortable handle that promotes a secure grip, further enhancing user control and comfort during operation.

In terms of safety, the Poulan 96192001200,407885 is equipped with a chain brake that engages automatically in the event of kickback. This critical safety feature helps prevent accidents, ensuring that users can work confidently while minimizing risk. Additionally, the chainsaw has an adjustable chain oiling system, which allows users to manage oil flow based on their cutting needs, ensuring the chain operates smoothly and reduces wear.

The chainsaw also features a 16-inch cutting bar, providing a balance between cutting capacity and maneuverability. This size is ideal for a variety of tasks, including cutting firewood, felling small trees, and pruning large branches.

Overall, the Poulan 96192001200,407885 is a reliable and efficient chainsaw that combines power, safety, and user-friendly features, making it an essential tool for homeowners and professionals alike. Whether for yard maintenance or more demanding forestry tasks, this chainsaw promises to deliver exceptional performance every time it is put to use.
Top Page Image Contents