Poulan 407885 To Remove Wheels See Fig, Remove the klik pin and remove wheel from axle

Page 17

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt

must be fully seated in pulley groove when bringing

 

the snow thrower together.

17

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

HOUSING

 

 

FIG. 23

TO REMOVE WHEELS (See Fig. 24)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 24

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigKnow Your Snow Thrower OperationRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting 5518 KEY Part Description 205 183334 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive Repair Parts Snow Thrower Model PP10530ES Drive Page KEY Part Description Repair Parts Repair Parts Limited Warranty

407885, 96192001200 specifications

The Poulan 96192001200,407885 is a high-performance gas-powered chainsaw designed to meet the needs of both casual users and professionals. This versatile tool is engineered with advanced technologies and features that enhance its efficiency, usability, and durability, making it a preferred choice for various cutting tasks.

One of the standout characteristics of the Poulan 96192001200,407885 is its powerful engine. The chainsaw is equipped with a robust 40cc 2-cycle engine, which provides ample power for heavy-duty cutting and trimming tasks. This engine delivers a reliable and consistent cutting performance, allowing users to tackle thicker branches and larger logs with ease.

The chainsaw incorporates an easy-start system, which significantly reduces the effort required to start the engine. This technology is particularly beneficial for users who may struggle with traditional starting mechanisms, allowing for a hassle-free experience right from the beginning.

Another notable feature of the Poulan chainsaw is its lightweight design. Weighing in at just around 10 pounds, this chainsaw is easy to maneuver, making it suitable for extended use without causing excessive fatigue. This ergonomic design is complemented by a comfortable handle that promotes a secure grip, further enhancing user control and comfort during operation.

In terms of safety, the Poulan 96192001200,407885 is equipped with a chain brake that engages automatically in the event of kickback. This critical safety feature helps prevent accidents, ensuring that users can work confidently while minimizing risk. Additionally, the chainsaw has an adjustable chain oiling system, which allows users to manage oil flow based on their cutting needs, ensuring the chain operates smoothly and reduces wear.

The chainsaw also features a 16-inch cutting bar, providing a balance between cutting capacity and maneuverability. This size is ideal for a variety of tasks, including cutting firewood, felling small trees, and pruning large branches.

Overall, the Poulan 96192001200,407885 is a reliable and efficient chainsaw that combines power, safety, and user-friendly features, making it an essential tool for homeowners and professionals alike. Whether for yard maintenance or more demanding forestry tasks, this chainsaw promises to deliver exceptional performance every time it is put to use.
Top Page Image Contents