Poulan 96192002400 Chute Weldment, Deflector Weldment, Deflector Control Assembly, Deflector Seal

Page 24

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002400)

CONTROL PANEL / CHUTE

5

7

3

14

15

			*13	*10
				*10
				*9
			2	*8
				*8
KEY	PART		4	6
			4
		DESCRIPTION
NO.	NO.	DESCRIPTION
1	404770X505	CHUTE WELDMENT	6
2	178633X505	DEFLECTOR WELDMENT	6	*12
3	420673	DEFLECTOR CONTROL ASSEMBLY		*12
4	420325	DEFLECTOR SEAL
5	414280	KNOB BLACK	1
6	128415	POP RIVET		*11
7	17501010	SCREW 10−24 X .625
*8	179829	SHOULDER SCREW
*9	179246	PLASTIC WASHER
*10	191730	NUT 1/4−20		01.09.002-B
*11	72250505	CARRIAGE BOLT 5/16−18 X .50		01.09.002-B
*12	751153	NUT 5/16−18
*13	184505	DEFLECTOR SPRING

14420679 (SERVICE PART) DEFLECTOR CONTROL HEAD

15420672 (SERVICE PART) DEFLECTOR CONTROL CABLE

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 14 AND 15 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 24

Image 24

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleRemove plastic tie securing rod to lower handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer TractionMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeAuger control lever used to engage auger motion throw snow Distance the snow is thrownHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineTo Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Housing Scrapper BARCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 LH Auger Assembly 30 RH420497X479 420498X479Deflector Control Assembly Chute WeldmentDeflector Weldment Deflector SealLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotLoop Handle LH Loop Handle RH405784X479 Pivot Support Weldment Spacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT1053ES Drive 43 420900 Drive Plate Assembly END PlateWasher Control ARM01.03.002-A KEY Part Description ENGINE, TEC Model LH358SA-159628A409346X505 Frame 417014X505 Engine Mount PlateBelt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower - Model Number XT1053ES Wheels Cable Bracket LH Cable Bracket RHCover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 35062181037 DECAL, DangerDECAL, Poulan PRO XT 10.5 HP/30 DECAL, DANGER, DeflectorService Notes Limited Warranty