Poulan 96192002400 KEY Part Description ENGINE, TEC, Model LH358SA-159628A, 409346X505 Frame

Page 33

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002400)

CHASSIS / ENGINE / PULLEYS

01.00.008-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
-	- - - - - -	ENGINE, TEC
		(MODEL LH358SA-159628A)

1409346X505 FRAME

2417014X505 ENGINE MOUNT PLATE

3	150406	BOLT 3/8−16
4	150078	SCREW 5/16−18 X .750

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 33

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleRemove plastic tie securing rod to lower handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer TractionDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsAuger control lever used to engage auger motion throw snow Distance the snow is thrownStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 RH Auger Assembly 30 LH420497X479 420498X479Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle LH Loop Handle RH405784X479 Pivot Support Weldment Retainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT1053ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARM01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC409346X505 Frame 417014X505 Engine Mount PlateBelt Cover Traction BeltImpeller Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number XT1053ES WheelsWheel Driver Retainer Ring CoverWheel Lobe Clutch Slide35062 Safety Ignition KEYDECAL, Danger 181037DECAL, Poulan PRO XT 10.5 HP/30 DECAL, DANGER, DeflectorService Notes Limited Warranty

KEY

PART

DESCRIPTION

ENGINE, TEC

(MODEL LH358SA-159628A)

1409346X505 FRAME

2417014X505 ENGINE MOUNT PLATE