Poulan 422077 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot

Page 25

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002400)

CONTROL PANEL / CHUTE

KEY	PART	*6
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	420337	LEVER/CABLE ROTATOR ASSEMBLY
2	17501010	SCREW 10−24 X .625
*3	420678	ROTATOR HEAD	*4	01.09.007-A
*4	420677	ROTATOR PIVOT BRACKET	*4		*5


*5	420675	PULLEY PIVOT
*6	420674	CABLE ASSEMBLY

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

01.15.005-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	188303	STEER CABLE
2	74041024	SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Image 25

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsRemove plastic tie securing rod to lower handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer TractionDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsAuger control lever used to engage auger motion throw snow Distance the snow is thrownStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 RH Auger Assembly 30 LH420497X479 420498X479Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle RH Loop Handle LH405784X479 Pivot Support Weldment Retainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT1053ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARM01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC409346X505 Frame 417014X505 Engine Mount PlateTraction Belt Belt CoverImpeller Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number XT1053ES WheelsWheel Driver Retainer Ring CoverWheel Lobe Clutch Slide35062 Safety Ignition KEYDECAL, Danger 181037DECAL, Poulan PRO XT 10.5 HP/30 DECAL, DANGER, DeflectorService Notes Limited Warranty

KEY

LEVER/CABLE ROTATOR ASSEMBLY

ROTATOR HEAD

ROTATOR PIVOT BRACKET

PULLEY PIVOT

KEY

STEER CABLE