Poulan XT1053ES, 96192002400, 422077 Unfold Upper Handle, Install Speed Control ROD See Figs

Page 5

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1. Remove plastic tie securing rod to lower handle.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

2.Insert rod into speed control bracket and secure with retainer spring.install traction DRIVE control rod (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP OPEN-

ING DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

5

Image 5

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonRemove plastic tie securing rod to lower handle Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer TractionDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsAuger control lever used to engage auger motion throw snow Distance the snow is thrownStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 RH Auger Assembly 30 LH420497X479 420498X479Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot405784X479 Pivot Support Weldment Loop Handle LHLoop Handle RH Retainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT1053ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARM01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC409346X505 Frame 417014X505 Engine Mount PlateImpeller Belt Belt CoverTraction Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number XT1053ES WheelsWheel Driver Retainer Ring CoverWheel Lobe Clutch Slide35062 Safety Ignition KEYDECAL, Danger 181037DECAL, Poulan PRO XT 10.5 HP/30 DECAL, DANGER, DeflectorService Notes Limited Warranty