Poulan 421281, 96192002001 owner manual Engine, Cleaning

Page 15

MAINTENANCE

BELTS

Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

Be sure snow thrower is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

Keep finished surfaces/wheels free of gasoline, oil, etc.

We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Image 15
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Unfold Upper HandleRemove plastic tie securing rod to lower handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerDistance the snow is thrown Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Auger control lever used to engage auger motion throw snowStopping HOW to USE Your Snow ThrowerRelease the auger control lever and shut off the engine Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingAuger 27 RH 420495X479Auger 27 LH 420496X479Deflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketLoop Handle LH Loop Handle RH405784X479 Pivot Support Weldment Handle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number PP10527ES Drive Bottom PAN Speed Selector AssemblyDrive Plate Assembly END Plate01.03.002-A 417014X428 Engine Mount Plate KEY Part Description ENGINE, TECModel LH358SA-159628A 409346X428 FrameBelt Cover Traction BeltImpeller Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number PP10527ES WheelsClutch Slide CoverWheel Driver Retainer Ring Wheel Lobe35062 Safety Ignition KEYDECAL, Danger 181037DECAL, Danger DECAL, Poulan PRO DECAL, DANGER, DeflectorService Notes Limited Warranty

421281, 96192002001 specifications

The Poulan 421281,96192002001 is a high-performance lawn and garden tool that stands out for its powerful capabilities and user-friendly features. Designed for both homeowners and professionals, this model offers a blend of efficiency, durability, and innovation that makes yard work manageable and even enjoyable.

At the core of the Poulan 421281 is its robust engine that delivers strong performance, ensuring it can tackle even the toughest gardening tasks. With an easy-start mechanism, users can fire up the machine with minimal effort, reducing the frustration often associated with traditional equipment. This engine is designed to provide ample power while maintaining fuel efficiency, allowing users to complete their tasks without frequent refueling.

One of the key features of the Poulan 421281 is its ergonomic design. The tool is equipped with a comfortable grip that reduces fatigue during extended use. This attention to user comfort is complemented by a well-balanced structure, making the tool easy to maneuver across various landscapes, whether trimming hedges or managing grass heights.

The Poulan 421281 also integrates advanced technologies to enhance its functionality. This includes adjustable speed settings, enabling the user to customize performance according to specific tasks. Additionally, the tool incorporates a quick-release mechanism for its attachments, which allows for fast and seamless switching between different tasks, further enhancing productivity.

Durability is another critical aspect of the Poulan 421281. Constructed with high-quality materials, this tool is built to withstand the rigors of outdoor use. The components are designed to resist wear and tear, ensuring a long service life and minimizing the need for frequent repairs.

Moreover, safety features are thoughtfully included to protect the user. The Poulan 421281 is equipped with a safety lock-out mechanism that prevents accidental starts, providing peace of mind.

In conclusion, the Poulan 421281,96192002001 is an exceptional tool for anyone looking to maintain their lawn and garden effectively. Its powerful engine, user-friendly design, innovative technologies, and durable construction make it a reliable choice for both casual gardeners and professionals alike. Whether you're tackling tough overgrowth or simply maintaining your yard, this Poulan model is equipped to handle the job efficiently and safely.