Poulan 96198003102, 437953 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klik pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Auger Bearing Auger HousingScrapper BAR CARRIAGEBOLT5/16−18X.625Skid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LHPlastic Washer Weight BARDrift Cutter BAR CARRIAGEBOLT5/16−18X.750Deflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldRepair Parts Snow Thrower Model PP414EPS30 Handles Pivot Support Weldment Loop Handle LHLoop Handle RH Lower HandleWasher 3/8 SpacerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP414EPS30 Drive Axle ShaftSprocket Exploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM BracketRepair Parts Snow Thrower Model PP414EPS30 Wheels Wheel Assembly LH Cable Bracket LHCable Bracket RH Repair Parts Snow Thrower Model PP414EPS30 BAG of Parts Safety Ignition KEY422663 Repair Parts Snow Thrower Model PP414EPS30 Decals Service Notes Service Notes Limited Warranty

437953, 96198003102 specifications

The Poulan 96198003102,437953 is a remarkable piece of outdoor equipment designed to make lawn care tasks effortless and efficient. This powerful tool has become a favorite among homeowners and professionals alike, thanks to its robust features and innovative technologies.

At the heart of the Poulan 96198003102,437953 is a high-performance engine that provides reliable power for a variety of cutting and trimming tasks. This engine is designed for durability and longevity, ensuring that the equipment can withstand the rigors of regular use. Its gas-powered design means you won’t be tethered to a power outlet, allowing for greater mobility and convenience while tackling larger areas.

One of the standout features of this equipment is its advanced cutting system. The Poulan 96198003102,437953 comes equipped with a precision blade that delivers clean and efficient cuts. The sharp, durable design allows for cutting through tougher grass and weeds with ease, ensuring a neat and tidy lawn. Additionally, the adjustable height settings enable users to customize the cutting height, making it suitable for various types of grass and terrain.

Comfort and usability have also been prioritized in this model. The ergonomic handle provides a comfortable grip, reducing strain on the user’s hands and wrists during extended use. The lightweight design contributes to ease of maneuverability, allowing users to navigate through tight spaces without difficulty. Furthermore, the tool features an easy start mechanism which simplifies the startup process, making it accessible for users of all skill levels.

For those concerned about environmental impact, the Poulan 96198003102,437953 incorporates technologies that promote fuel efficiency and reduced emissions. This is particularly important in today’s eco-conscious market, where consumers are looking for tools that align with their values while still delivering performance.

In addition to its powerful engine and sharp cutting system, the Poulan 96198003102,437953 offers minimal maintenance requirements. This is a significant advantage for users, as it means less time spent on upkeep and more time enjoying a well-manicured lawn.

Overall, the Poulan 96198003102,437953 stands out in its category for its combination of power, efficiency, and user-friendly design. Whether you're maintaining your backyard or tackling larger landscaping projects, this versatile tool is equipped to get the job done effectively and effortlessly. Its blend of innovative technologies and user-focused features makes it a top choice for outdoor enthusiasts looking for reliability and performance.
Top Page Image Contents