Poulan 96198003102, 437953 owner manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 23)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.

REMOVE HAIRPIN FROM CLUTCH ROD and re-

 

move clutch rod from swing plate. Tip swing plate

 

forward.

7.

REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

BOLT

 

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

 

IDLER ARM

 

 

 

BRACKET

 

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

 

17

FIG. 23

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 RH Auger Assembly 30 LHSkid Plate LH Skid Plate RHDrift Cutter BAR Weight BARCARRIAGEBOLT5/16−18X.750 Plastic WasherChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadRepair Parts Snow Thrower Model PP414EPS30 Handles Loop Handle RH Loop Handle LHLower Handle Pivot Support WeldmentKnob RED SpacerHandle Knob Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Sprocket Repair Parts Snow Thrower Model PP414EPS30 DriveAxle Shaft Exploded Drive Plate Assembly AssemblySpeed Selector Rubber RingFrame Complete LCT Engine427963X428 Engine Mounting PlateTraction Belt Impeller BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PP414EPS30 Wheels Cable Bracket RH Wheel Assembly LHCable Bracket LH 422663 Repair Parts Snow Thrower Model PP414EPS30 BAG of PartsSafety Ignition KEY Repair Parts Snow Thrower Model PP414EPS30 Decals Service Notes Service Notes Limited Warranty

437953, 96198003102 specifications

The Poulan 96198003102,437953 is a remarkable piece of outdoor equipment designed to make lawn care tasks effortless and efficient. This powerful tool has become a favorite among homeowners and professionals alike, thanks to its robust features and innovative technologies.

At the heart of the Poulan 96198003102,437953 is a high-performance engine that provides reliable power for a variety of cutting and trimming tasks. This engine is designed for durability and longevity, ensuring that the equipment can withstand the rigors of regular use. Its gas-powered design means you won’t be tethered to a power outlet, allowing for greater mobility and convenience while tackling larger areas.

One of the standout features of this equipment is its advanced cutting system. The Poulan 96198003102,437953 comes equipped with a precision blade that delivers clean and efficient cuts. The sharp, durable design allows for cutting through tougher grass and weeds with ease, ensuring a neat and tidy lawn. Additionally, the adjustable height settings enable users to customize the cutting height, making it suitable for various types of grass and terrain.

Comfort and usability have also been prioritized in this model. The ergonomic handle provides a comfortable grip, reducing strain on the user’s hands and wrists during extended use. The lightweight design contributes to ease of maneuverability, allowing users to navigate through tight spaces without difficulty. Furthermore, the tool features an easy start mechanism which simplifies the startup process, making it accessible for users of all skill levels.

For those concerned about environmental impact, the Poulan 96198003102,437953 incorporates technologies that promote fuel efficiency and reduced emissions. This is particularly important in today’s eco-conscious market, where consumers are looking for tools that align with their values while still delivering performance.

In addition to its powerful engine and sharp cutting system, the Poulan 96198003102,437953 offers minimal maintenance requirements. This is a significant advantage for users, as it means less time spent on upkeep and more time enjoying a well-manicured lawn.

Overall, the Poulan 96198003102,437953 stands out in its category for its combination of power, efficiency, and user-friendly design. Whether you're maintaining your backyard or tackling larger landscaping projects, this versatile tool is equipped to get the job done effectively and effortlessly. Its blend of innovative technologies and user-focused features makes it a top choice for outdoor enthusiasts looking for reliability and performance.
Top Page Image Contents