Poulan 96198003102, 437953 owner manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

MUFFLER

GASOLINE

FILLER CAP

CHOKE

CON-

TROL

SAFETY

IGNITION

KEY

ON / OFF

SWITCH

PRIMER

FUEL SHUT-OFF VALVE

RECOIL (AUXILIARY) STARTER HANDLE

ELECTRIC	AUGER	DISCHARGE CHUTE CONTROL LEVER
START	CONTROL
BUTTON	LEVER	DRIVE SPEED	DEFLECTOR REMOTE
		DRIVE SPEED	CONTROL LEVER
		CONTROL LEVER	CONTROL LEVER
POWER		CONTROL LEVER
POWER
CORD
PLUG	CHUTE		TRACTION
			TRACTION
			DRIVE
	DEFLECTOR		DRIVE
	DEFLECTOR		CONTROL
			CONTROL
			LEVER

LH TURN

TRIGGER

DISCHARGE

CHUTE

LIGHT

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT.

AUGERS

CLEAN-OUT TOOL

FIG. 10

HANDLE

KNOB

MUFFLER

TOOLBOX

DRIFT CUTTER

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Drift cutter - used to cut through deep snowdrifts.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

Deflector remote control lever - used to change the distance the snow is thrown.

9

Image 9

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger BearingAuger Assembly 30 RH Auger Assembly 30 LHSkid Plate LH Skid Plate RHDrift Cutter BAR Weight BARCARRIAGEBOLT5/16−18X.750 Plastic WasherChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadRepair Parts Snow Thrower Model PP414EPS30 Handles Loop Handle RH Loop Handle LHLower Handle Pivot Support WeldmentKnob RED SpacerHandle Knob Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP414EPS30 Drive Axle ShaftSprocket Exploded Drive Plate Assembly AssemblySpeed Selector Rubber RingFrame Complete LCT Engine427963X428 Engine Mounting PlateTraction Belt Impeller BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PP414EPS30 Wheels Wheel Assembly LH Cable Bracket LHCable Bracket RH Repair Parts Snow Thrower Model PP414EPS30 BAG of Parts Safety Ignition KEY422663 Repair Parts Snow Thrower Model PP414EPS30 Decals Service Notes Service Notes Limited Warranty