Poulan PR1330ES, 428553, 96192003200, PP1330ES owner manual Engine, Cleaning

Page 15

MAINTENANCE

BELTS

Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting KEY Part Description 23 22 Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingAuger Assembly 30 RH Auger Assembly 30 LHPlastic Washer Weight BARDrift Cutter BAR CARRIAGEBOLT5/16−18X.750Deflector Spring Knob BlackPOP Rivet Chute Snow Shield 419822X004 Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Loop Handle LHLoop Handle RH Lower TubeShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPHalogen Headlight Wire HarnessPanel Console Headlight BezelRepair Parts Snow Thrower - Model Number PP1330ES Drive Exploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector427963X428 Cover AssemblyComplete LCT Engine FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH Cable Bracket LHCable Bracket RH Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe422663 Safety Ignition KEYDECAL, Instruction 181037DECAL, Danger DECAL, DANGER, DeflectorLimited Warranty

PR1330ES, PP1330ES, 96192003200, 428553 specifications

The Poulan PP1330ES is a powerful and reliable chainsaw designed for both homeowners and professionals alike. Known for its robust performance, this model features a 33cc two-cycle engine which delivers ample power for a variety of cutting tasks. Whether trimming branches or tackling larger logs, the PP1330ES is up to the job.

One of its standout features is the effortless pull starting system. The EZ Start technology minimizes the effort required to start the engine, ensuring that users can get to work without the frustration that often accompanies traditional pull-start mechanisms. This is especially beneficial for those who may not be as physically strong or are new to using chainsaws.

The chainsaw incorporates a 16-inch cutting bar, which provides a great balance between portability and cutting capacity. This length is ideal for medium-sized trees and logs, making the PP1330ES versatile for various outdoor tasks. The chainsaw also comes with an automatic oiling system, which lubricates the chain during operation, enhancing both performance and longevity. This feature ensures that users spend less time on maintenance and more time cutting.

Safety is paramount in chainsaw design, and the PP1330ES does not disappoint. It includes a chain brake that initiates instantly in the event of kickback, protecting the user from potential accidents. The handle is ergonomically designed, providing a comfortable grip that reduces fatigue, allowing for extended use without discomfort.

Model 428553, part of the Poulan Pro series, features similar attributes and is engineered for durability. The inclusion of a heavy-duty air filter prolongs engine life by reducing debris, while the easy-access filter hastens maintenance checks.

The PR1330ES and model 96192003200 are also worth mentioning; both are designed with features that enhance performance and user experience. These models utilize advanced technologies like improved vibration dampening systems, which reduce operator fatigue during prolonged use, and innovative air injection systems that minimize airborne debris.

In summary, the Poulan PP1330ES, along with 428553, PR1330ES, and 96192003200, showcases a range of features that prioritize power, performance, and user safety. These chainsaws are equipped with technologies that enhance ease of use and maintenance, making them ideal for anyone looking to tackle outdoor cutting tasks efficiently and effectively. Whether you’re a weekend warrior or a seasoned professional, these Poulan chainsaws are sure to meet your needs.
Top Page Image Contents