Poulan 428553, PP1330ES Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

 

The impeller is secured to the impeller shaft with two (2)

 

capscrew/shear bolts and hex nuts. Should a foreign object

 

or ice become lodged in the impeller, the capscrews are

 

designed to break, preventing damage to any other com-

 

ponents. If impeller does not turn when auger control lever

 

is engaged, check to see if the capscrews have sheared.

16

To replace the capscrew/shear bolts:

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting KEY Part Description 23 22 Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Assembly 30 LH Auger Assembly 30 RHWeight BAR Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Plastic WasherKnob Black POP RivetChute Snow Shield 419822X004 Shield Retainer Strap Deflector SpringLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot SupportImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Panel ConsoleHeadlight Bezel Halogen HeadlightRepair Parts Snow Thrower - Model Number PP1330ES Drive Exploded Assembly Drive Plate AssemblySpeed Selector Rubber RingCover Assembly Complete LCT EngineFrame 427963X428Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyCable Bracket LH Wheel Assembly LHCable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 422663181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionLimited Warranty

PR1330ES, PP1330ES, 96192003200, 428553 specifications

The Poulan PP1330ES is a powerful and reliable chainsaw designed for both homeowners and professionals alike. Known for its robust performance, this model features a 33cc two-cycle engine which delivers ample power for a variety of cutting tasks. Whether trimming branches or tackling larger logs, the PP1330ES is up to the job.

One of its standout features is the effortless pull starting system. The EZ Start technology minimizes the effort required to start the engine, ensuring that users can get to work without the frustration that often accompanies traditional pull-start mechanisms. This is especially beneficial for those who may not be as physically strong or are new to using chainsaws.

The chainsaw incorporates a 16-inch cutting bar, which provides a great balance between portability and cutting capacity. This length is ideal for medium-sized trees and logs, making the PP1330ES versatile for various outdoor tasks. The chainsaw also comes with an automatic oiling system, which lubricates the chain during operation, enhancing both performance and longevity. This feature ensures that users spend less time on maintenance and more time cutting.

Safety is paramount in chainsaw design, and the PP1330ES does not disappoint. It includes a chain brake that initiates instantly in the event of kickback, protecting the user from potential accidents. The handle is ergonomically designed, providing a comfortable grip that reduces fatigue, allowing for extended use without discomfort.

Model 428553, part of the Poulan Pro series, features similar attributes and is engineered for durability. The inclusion of a heavy-duty air filter prolongs engine life by reducing debris, while the easy-access filter hastens maintenance checks.

The PR1330ES and model 96192003200 are also worth mentioning; both are designed with features that enhance performance and user experience. These models utilize advanced technologies like improved vibration dampening systems, which reduce operator fatigue during prolonged use, and innovative air injection systems that minimize airborne debris.

In summary, the Poulan PP1330ES, along with 428553, PR1330ES, and 96192003200, showcases a range of features that prioritize power, performance, and user safety. These chainsaws are equipped with technologies that enhance ease of use and maintenance, making them ideal for anyone looking to tackle outdoor cutting tasks efficiently and effectively. Whether you’re a weekend warrior or a seasoned professional, these Poulan chainsaws are sure to meet your needs.
Top Page Image Contents