Poulan 428553, 96192003200, PP1330ES, PR1330ES owner manual Troubleshooting

Page 20

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

ON/OFF switch is OFF

4.

ON/OFF switch to ON position

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service center/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service center/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service center/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

20

Image 20
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting KEY Part Description 23 22 Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Assembly 30 LH Auger Assembly 30 RHWeight BAR Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Plastic WasherKnob Black POP RivetChute Snow Shield 419822X004 Shield Retainer Strap Deflector SpringLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot SupportImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Panel ConsoleHeadlight Bezel Halogen HeadlightRepair Parts Snow Thrower - Model Number PP1330ES Drive Exploded Assembly Drive Plate AssemblySpeed Selector Rubber RingCover Assembly Complete LCT EngineFrame 427963X428Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyCable Bracket RH Wheel Assembly LHCable Bracket LH Cover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 422663181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionLimited Warranty

PR1330ES, PP1330ES, 96192003200, 428553 specifications

The Poulan PP1330ES is a powerful and reliable chainsaw designed for both homeowners and professionals alike. Known for its robust performance, this model features a 33cc two-cycle engine which delivers ample power for a variety of cutting tasks. Whether trimming branches or tackling larger logs, the PP1330ES is up to the job.

One of its standout features is the effortless pull starting system. The EZ Start technology minimizes the effort required to start the engine, ensuring that users can get to work without the frustration that often accompanies traditional pull-start mechanisms. This is especially beneficial for those who may not be as physically strong or are new to using chainsaws.

The chainsaw incorporates a 16-inch cutting bar, which provides a great balance between portability and cutting capacity. This length is ideal for medium-sized trees and logs, making the PP1330ES versatile for various outdoor tasks. The chainsaw also comes with an automatic oiling system, which lubricates the chain during operation, enhancing both performance and longevity. This feature ensures that users spend less time on maintenance and more time cutting.

Safety is paramount in chainsaw design, and the PP1330ES does not disappoint. It includes a chain brake that initiates instantly in the event of kickback, protecting the user from potential accidents. The handle is ergonomically designed, providing a comfortable grip that reduces fatigue, allowing for extended use without discomfort.

Model 428553, part of the Poulan Pro series, features similar attributes and is engineered for durability. The inclusion of a heavy-duty air filter prolongs engine life by reducing debris, while the easy-access filter hastens maintenance checks.

The PR1330ES and model 96192003200 are also worth mentioning; both are designed with features that enhance performance and user experience. These models utilize advanced technologies like improved vibration dampening systems, which reduce operator fatigue during prolonged use, and innovative air injection systems that minimize airborne debris.

In summary, the Poulan PP1330ES, along with 428553, PR1330ES, and 96192003200, showcases a range of features that prioritize power, performance, and user safety. These chainsaws are equipped with technologies that enhance ease of use and maintenance, making them ideal for anyone looking to tackle outdoor cutting tasks efficiently and effectively. Whether you’re a weekend warrior or a seasoned professional, these Poulan chainsaws are sure to meet your needs.