Poulan PP1330ES, 428553, 96192003200, PR1330ES To Remove Wheels See Fig, Carburetor, Engine Speed

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 24)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 24

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 25)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 25

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting KEY Part Description 23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyAuger Assembly 30 LH Auger Assembly 30 RHCARRIAGEBOLT5/16−18X.750 Weight BARDrift Cutter BAR Plastic WasherChute Snow Shield 419822X004 Shield Retainer Strap Knob BlackPOP Rivet Deflector SpringCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Loop Handle LHLoop Handle RH Pivot SupportShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomHeadlight Bezel Wire HarnessPanel Console Halogen HeadlightRepair Parts Snow Thrower - Model Number PP1330ES Drive Exploded Speed Selector AssemblyDrive Plate Assembly Rubber RingFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler PulleyWheel Assembly LH Cable Bracket LHCable Bracket RH Wheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 422663DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, InstructionLimited Warranty

PR1330ES, PP1330ES, 96192003200, 428553 specifications

The Poulan PP1330ES is a powerful and reliable chainsaw designed for both homeowners and professionals alike. Known for its robust performance, this model features a 33cc two-cycle engine which delivers ample power for a variety of cutting tasks. Whether trimming branches or tackling larger logs, the PP1330ES is up to the job.

One of its standout features is the effortless pull starting system. The EZ Start technology minimizes the effort required to start the engine, ensuring that users can get to work without the frustration that often accompanies traditional pull-start mechanisms. This is especially beneficial for those who may not be as physically strong or are new to using chainsaws.

The chainsaw incorporates a 16-inch cutting bar, which provides a great balance between portability and cutting capacity. This length is ideal for medium-sized trees and logs, making the PP1330ES versatile for various outdoor tasks. The chainsaw also comes with an automatic oiling system, which lubricates the chain during operation, enhancing both performance and longevity. This feature ensures that users spend less time on maintenance and more time cutting.

Safety is paramount in chainsaw design, and the PP1330ES does not disappoint. It includes a chain brake that initiates instantly in the event of kickback, protecting the user from potential accidents. The handle is ergonomically designed, providing a comfortable grip that reduces fatigue, allowing for extended use without discomfort.

Model 428553, part of the Poulan Pro series, features similar attributes and is engineered for durability. The inclusion of a heavy-duty air filter prolongs engine life by reducing debris, while the easy-access filter hastens maintenance checks.

The PR1330ES and model 96192003200 are also worth mentioning; both are designed with features that enhance performance and user experience. These models utilize advanced technologies like improved vibration dampening systems, which reduce operator fatigue during prolonged use, and innovative air injection systems that minimize airborne debris.

In summary, the Poulan PP1330ES, along with 428553, PR1330ES, and 96192003200, showcases a range of features that prioritize power, performance, and user safety. These chainsaws are equipped with technologies that enhance ease of use and maintenance, making them ideal for anyone looking to tackle outdoor cutting tasks efficiently and effectively. Whether you’re a weekend warrior or a seasoned professional, these Poulan chainsaws are sure to meet your needs.
Top Page Image Contents