Poulan 96198003602, 437921 Knob Black, POP Rivet, Chute Snow Shield, Shield Retainer Strap

Page 25

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003602)

CONTROL PANEL / CHUTE

5

7

15

3

16

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1435023X428 CHUTE WELDMENT

2178633X428 DEFLECTOR WELDMENT

3420673 DEFLECTOR CONTROL ASSEMBLY

4420325 DEFLECTOR SEAL

5	414280	KNOB BLACK
6	128415	POP RIVET

717501010 SCREW 10-24 X .625

8430324 CHUTE SNOW SHIELD

9	419822X431	SHIELD RETAINER STRAP	6
*10	179829	SHOULDER BOLT 1/4-20 X .375
*11	191730	NUT 1/4-20
*12	72250505	CARRIAGE BOLT 3/8-16 X .625
*13	751153	NUT 5/16-18
*14	184505	DEFLECTOR SPRING

15420679 (SERVICE PART) DEFLECTOR CONTROL

16420672 (SERVICE PART) DEFLECTOR CABLE BLK

*14		*11
		*11
2		*10
	6	*10
4	6
4

6	*13

1

*12

9

8 01.09.015-B

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

25

Image 25

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Auger HousingScraper BAR Auger 27 LHExploded 178675X431 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyBearing Plug Auger BearingSkid Plate LH Skid Plate RHPOP Rivet Knob BlackChute Snow Shield Shield Retainer StrapCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadLoop Handle RH Loop Handle LH427513X431 Pivot Support Weldment Retainer SpacerKnob RED Handle KnobTraction ROD Impeller RODConsole Panel Wire HarnessHeadlight Bezel Flood Headlight01.03.005-B Exploded Drive Plate Assembly Speed Selector AssemblyWheel HUB END PlateFrame Complete LCT Engine427963X428 Engine Mounting PlateTraction Belt Impeller BeltIdler ARM Bracket Idler Pulley432335X421 Wheel Assembly LH432336X421 422663 Safety Ignition KEYDECAL, Danger 181037Service Notes Limited Warranty