Poulan 96198003602 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Idler Bracket

Page 35

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003602)

CHASSIS / ENGINE / PULLEYS

27

23

22

			13
			21
			20
25
24
13	21		19
15			26
15					18
					18
11					17
					17
12					16
13		14			16
13		14
			7
		5
9
				4	6
				4
10			3		1
10					2
				8

01.21.020-B

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	419888	IMPELLER BELT
2	427304	TRACTION BELT
3	423723X431	IDLER ARM BRACKET
4	180523	IDLER PULLEY
5	423990X431	IDLER BRACKET
6	426589	NUT 5/16-18
7	74780524	SCREW 5/16-18 X 1.50
8	424297	SHOULDER BOLT 5/16-18 X .50
9	751153	NUT 5/16-18 LOCK
10	428867	SCREW 5/16-18 X .625

11427576 TRACTION IDLER BRACKET

12180522 TRACTION PULLEY

13	59289	WASHER
14	73800500	NUT 5/16-18

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
15	74780520	SCREW 5/16-18 X 1.25
16	851084	SCREW 3/8-24 X 1 .375
17	19132005	WASHER

18425934 PULLEY ENG IMPELLER

19425933 PULLEY ENG TRACTION

2074610516 SCREW 5/16-24 X 1.00

2110040500 LOCKWASHER 5/16

22

155452

BELT GUIDE

2311050500 LOCKWASHER 5/16

24175331 IDLER BUSHING

2519112206 WASHER

2674610520 SCREW 5/16-24 X 1.25

2774760608 SCREW 3/8-16 X .750

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 35

Image 35

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Auger 27 LH Auger HousingKEY Part Description Scraper BARExploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool BearingSkid Plate RH Auger BearingBearing Plug Skid Plate LHShield Retainer Strap Knob BlackPOP Rivet Chute Snow ShieldRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat Shield427513X431 Pivot Support Weldment Loop Handle LHLoop Handle RH Handle Knob SpacerRetainer Knob REDTraction ROD Impeller RODFlood Headlight Wire HarnessConsole Panel Headlight Bezel01.03.005-B Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUBEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket432336X421 Wheel Assembly LH432335X421 422663 Safety Ignition KEYDECAL, Danger 181037Service Notes Limited Warranty