Poulan 437921 Parts Packed Separately in Carton, Assembly / PRE-OPERATION, Tool BOX See Fig

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) POWER CORD

(1) MULTI-

(3) RETAINER

(198563)

WRENCH

SPRINGS

 

 

(180684)

(169675)

 

(2) SHEAR BOLTS 1/4-20 x 1-3/4

(2) LOCKNUTS

 

 

1/4-20

 

(192090)

 

 

 

(73800400)

 

 

 

(2) FLAT WASHERS

 

 

 

 

SAFTEY

 

 

 

IGNITION KEY (S)

 

 

 

(422663)

 

 

(2) CARRIAGE BOLTS

(1) LOCKNUT

(1) CARRIAGE BOLT

3/8-16 x 2.25

5/16-18

 

5/16-18 x 5/8

 

(751153)

 

(72250505)

 

(1) WASHER 3/8

(1) LOCKNUT 3/8

(1) LOCKNUT

(1) SHOULDER

 

(2) HANDLE KNOBS

1/4-20

BOLT 1/4-20

(1) SPRING

(19131316)

(73800600)

(191730)

(179829)

(184505)

 

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing KEY Part DescriptionScraper BAR Auger 27 LHExploded Gearbox Assembly 178675X431 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Bearing Bearing PlugSkid Plate LH Skid Plate RHKnob Black POP RivetChute Snow Shield Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle RH Loop Handle LH427513X431 Pivot Support Weldment Spacer RetainerKnob RED Handle KnobImpeller ROD Traction RODWire Harness Console PanelHeadlight Bezel Flood Headlight01.03.005-B Exploded Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler Pulley432335X421 Wheel Assembly LH432336X421 Safety Ignition KEY 422663181037 DECAL, DangerService Notes Limited Warranty
Top Page Image Contents