Poulan 437921 Console Panel, Headlight Bezel, Flood Headlight, Shoulder Screw 10−24, Wire Harness

Page 30

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003602)

HANDLES

			1	KEY	PART
	5	4	1	NO.	NO.	DESCRIPTION
		4		NO.	NO.	DESCRIPTION
6				1	182906	CONSOLE PANEL
6				1	182906	CONSOLE PANEL
				2	178668	HEADLIGHT BEZEL
				3	180927	FLOOD HEADLIGHT
		01.10.007-B		4	184471	SHOULDER SCREW 10−24 X
		01.10.007-B				.625
				5	175262	SCREW 10−24 X 1.25
				6	178770	WIRE HARNESS
				7	183784	BULB

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
	3	1	412675X431	INTERLOCK SPRING
	2	2	414572	INTERLOCK CAM
5	2	3	178831	TORSION SPRING
		4	169675	RETAINER
		5	17060410	SCREW 1/4−20 X .625
	1	6	421252X431	INTERLOCK STOP
	1
6	01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 30

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Scraper BAR Auger HousingKEY Part Description Auger 27 LHExploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller PulleySkid Plate LH Auger BearingBearing Plug Skid Plate RHChute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLoop Handle LH Loop Handle RH427513X431 Pivot Support Weldment Knob RED SpacerRetainer Handle KnobImpeller ROD Traction RODHeadlight Bezel Wire HarnessConsole Panel Flood Headlight01.03.005-B Exploded Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate427963X428 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler PulleyWheel Assembly LH 432335X421432336X421 Safety Ignition KEY 422663181037 DECAL, DangerService Notes Limited Warranty

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003602)

KEY

CONSOLE PANEL

HEADLIGHT BEZEL

FLOOD HEADLIGHT

SHOULDER SCREW 10−24 X

WIRE HARNESS

BULB

KEY

INTERLOCK SPRING

INTERLOCK CAM

TORSION SPRING

RETAINER

INTERLOCK STOP