Poulan 429884 owner manual Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 19)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 19

TO REMOVE BELT COVER (See Fig. 20)

1.Remove the two screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

FRAME

BELT COVER

SCREWS

FIG. 20

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes 23 22 KEY Part Description Auger Housing Auger Assembly 30 LHAuger Assembly 30 RH Scrapper BARAuger Bearing Bearing PlugKnob Black POP RivetShoulder Screw Deflector SpringLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model XT11530ES Handles Loop Handle LHLoop Handle RH Lower Tube180480 Impeller RODTraction ROD RetainerSpacer Knob REDHandle Knob Washer 3/8Wire Harness Interlock SpringInterlock CAM Torsion SpringRepair Parts Snow Thrower Model XT11530ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingAxle Shaft SprocketEngine Model Frame423185X505 Engine Mounting Plate428684 Repair Parts Snow Thrower Model XT11530ES Wheels 01.06.005-A Safety Ignition KEY Repair Parts Snow Thrower Model XT11530ES BAG of Parts193071 Repair Parts Snow Thrower Model XT11530ES Decals 181037DECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Service Notes Limited Warranty

429884, 96192003501 specifications

The Poulan 96192003501,429884 is a powerful and versatile tool designed for outdoor maintenance, particularly for those who require a robust chainsaw for various tasks. This model is engineered with performance and efficiency in mind, making it an ideal choice for both professional landscapers and homeowners looking to tackle yard work with ease.

One of the standout features of the Poulan 96192003501,429884 is its advanced engine technology. The chainsaw is equipped with a reliable two-stroke engine that provides plenty of power for cutting through wood with minimal effort. This means users can expect quick and efficient performance, whether they are felling trees, trimming branches, or cutting firewood.

Safety is a top priority in the design of this chainsaw. It features an automatic chain oiler, ensuring the chain remains well-lubricated during operation, which not only prolongs the life of the chain but also reduces friction and heat buildup. Additionally, the Poulan chainsaw incorporates a low kickback chain, designed to minimize the risk of kickback during cutting, making it safer for users, especially beginners.

The Poulan 96192003501,429884 is also designed for user comfort. It features an ergonomic handle that offers a comfortable grip, reducing fatigue during extended use. The chainsaw's lightweight design enhances portability, allowing users to maneuver it easily in various environments, from dense woods to open fields.

Another notable characteristic is its easy-start technology. With this feature, starting the chainsaw is straightforward, requiring less effort to get the engine running smoothly. This convenience is particularly beneficial for those who may struggle with traditional starting mechanisms.

In summary, the Poulan 96192003501,429884 is a highly functional chainsaw that combines power, safety, and user-friendly features. Its advanced engine technology, automatic chain oiler, low kickback chain, ergonomic design, and easy-start capabilities make it an excellent choice for those looking to maintain their outdoor spaces efficiently and safely. Whether for professional landscaping or home improvement projects, this chainsaw stands out as a reliable tool for tackling a variety of cutting tasks.
Top Page Image Contents